LAN Setup Help Needed

[Htnut]

I am new to IP office and have found my way around most things so far but I am struggling with anything related to the WAN

I am having issues with registering SIP clients on the WAN and Voicemail to email not being able to connect with the SMTP server

I suspect that I am not understanding the relationship between LAN 1 and LAN 2. Are they equivalent?

What is the recommended configuration for a system of eight 9608 phones, four Iphone SIP clients a Drey8320 router and an small office LAN?

I currently have the IPO connected to the LAN via LAN 1. Is this the source of my problems?

 

[tlpeter]

You have two different issues.
First the SMTP.
Where did you configure the SMTP settings for voicemail to email?
Use monitor and set a filter for SMTP
Then leave a message and see what it tells you.

Then the sip clients, do they register?
Drayteks do inspect packages, turn that off.


BAZINGA!

I'm not insane, my mother had me tested!

 

[Htnut]

I have now got the voice mail to email to work on LAN 1

I still have the issue of the IPhone SIP clients not registering when on the WAN. I have no problem when on the LAN

I have looked in monitor and there are no registration requests being received in IPO when on the WAN.

I have done the following:

DRAYTEK SETTINGS:

IPO LAN 1 address to DMZ Active True IP
strict firewall: unticked
Opened port 5060 (just in case!)

IPO SETTINGS

Firewall NAT Type: Static port block
Public address : My public address
Public port: 5060

IP Route
IP= 0.0.0.0
Subnet mask 0.0.0.0
Gateway= router address
Destination LAN1

Is there something I have missed or got wrong?

 

[tlpeter]

Be careful with putting the IPO in a DMZ!
You should be able to connect with manager.
What SIP clients do you use?


BAZINGA!

I'm not insane, my mother had me tested!

 

[amriddle01]

You will also need SIP ALG turning off, you need to telnet into the router to do this, I think it's SYS SIP_ALG = 0 or similar, also depending on how badly Draytek have written the firmware it may never work without rolling back a few levels

 

[Westi]

have the STUN server active so that it discovers the public IP address even though it is static it might have several and goes out another public IP.
I also had it that I could only make it work when STUn was on even though the public IP was correct.

Joe W.

FHandw, ACSS

 

[Htnut]

Thanks for the suggestions amriddle and Westi

I have tried both suggestions.

I saw this in the monitor log


70321069mS H323Evt: Recv: RegistrationRequest 192.168.0.120; Endpoints registered: 1; Endpoints in registration: 0
70327646mS RES: Mon 7/5/2012 11:41:17 FreeMem=62590512(3) CMMsg=6 (7) Buff=5200 960 999 7463 5 Links=8354
70327646mS RES2: IP 500 V2 8.0(42) Tasks=42 RTEngine=0 CMRTEngine=0 ExRTEngine=0 Timer=49 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=18 TAPI=0 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
70328937mS PRN: Create STUN client for LAN1 c0a8006e
70339646mS RES: Mon 7/5/2012 11:41:28 FreeMem=62577104(3) CMMsg=6 (7) Buff=5200 960 999 7462 5 Links=8349
70339646mS RES2: IP 500 V2 8.0(42) Tasks=42 RTEngine=0 CMRTEngine=0 ExRTEngine=0 Timer=52 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=19 TAPI=0 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
70359316mS SIP Rx: UDP 178.238.134.190:3478 -> 192.168.0.110:5060



70376076mS H323Evt: Recv: RegistrationRequest 192.168.0.120; Endpoints registered: 1; Endpoints in registration: 0
70416146mS RES: Mon 7/5/2012 11:42:44 FreeMem=62583760(3) CMMsg=6 (7) Buff=5200 959 1000 7463 5 Links=8322
70416146mS RES2: IP 500 V2 8.0(42) Tasks=42 RTEngine=0 CMRTEngine=0 ExRTEngine=0 Timer=48 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=18 TAPI=0 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
70422146mS RES: Mon 7/5/2012 11:42:51 FreeMem=62588076(3) CMMsg=6 (7) Buff=5200 960 1000 7463 5 Links=8351
70422146mS RES2: IP 500 V2 8.0(42) Tasks=42 RTEngine=0 CMRTEngine=0 ExRTEngine=0 Timer=50 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=18 TAPI=0 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
70427146mS RES: Mon 7/5/2012 11:42:56 FreeMem=62578476(3) CMMsg=6 (7) Buff=5200 960 1000 7463 5 Links=8349
70427146mS RES2: IP 500 V2 8.0(42) Tasks=42 RTEngine=0 CMRTEngine=0 ExRTEngine=0 Timer=51 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=19 TAPI=0 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
70431082mS H323Evt: Recv: RegistrationRequest 192.168.0.120; Endpoints registered: 1; Endpoints in registration: 0
70455666mS SIP Rx: UDP 178.238.134.189:3478 -> 192.168.0.110:5060



Does this mean that Stun is successfully enabled?

I still cannot register the phone.

I am testing using my mobile 3G for the phone.

Is it possible that my mobile provider is blocking SIP?