Jbconfig not seeing VTL

[terrywashington]

I am attempting to add a second Sepaton virtual tape library to our Solaris 9 (Sun Fire V440) Networker (7.2.2) server. I did not add the first Sepaton VTL so I am rather new at this. Both Sepatons and the V440 are connected to a Brocade switch which which is zoned. I am able to see the new sepaton (emulating an ATL P7000 16 drive library) in probe-scsi-all output as seen below. The first sepaton is emulating an ATL P1000 6 drive library. I am able to see the new sepaton in cfgadm output and I see the tape drives in /dev/rmt. I do not see the new sepaton listed in inquire output and it is not listed when I run jbconfig to add it to networker. I am thinking that something may need to be added to /kernel/dev/st.conf. However there are no entries for the first sepaton in st.conf and it works fine. Does anyone have any advice? I have service calls open with Sepaton support and EMC but am not making any progress.


3} ok probe-scsi-all

/pci@1f,700000/scsi@2,1



/pci@1f,700000/scsi@2

Target 0

Unit 0 Disk CSC 73GB10K REFURBISHED 0125 143374744 Blocks, 70007 MB

Target 1

Unit 0 Disk CSC 73GB10K REFURBISHED 0125 143374744 Blocks, 70007 MB

Target 2

Unit 0 Disk SEAGATE ST373307LSUN72G 0507 143374738 Blocks, 70007 MB

Target 3

Unit 0 Disk HP 73.4GST373405LC HP03 143374738 Blocks, 70007 MB



/pci@1e,600000/scsi@3,1



/pci@1e,600000/scsi@3



/pci@1e,600000/scsi@2,1



/pci@1e,600000/scsi@2



/pci@1c,600000/SUNW,qlc@1

************************* Fabric Attached Devices ************************

Adapter portId - 10700

Device PortId 10100 DeviceId 0 WWPN 100000068d041100

Lun 0 CHANGER ATL P7000 R210



Lun 1 TAPE IBM ULTRIUM-TD3 57GA



Lun 2 TAPE IBM ULTRIUM-TD3 57GA



Lun 3 TAPE IBM ULTRIUM-TD3 57GA



Lun 4 TAPE IBM ULTRIUM-TD3 57GA



Lun 5 TAPE IBM ULTRIUM-TD3 57GA



Lun 6 TAPE IBM ULTRIUM-TD3 57GA



Lun 7 TAPE IBM ULTRIUM-TD3 57GA



Lun 8 TAPE IBM ULTRIUM-TD3 57GA



Lun 9 TAPE IBM ULTRIUM-TD3 57GA



Lun a TAPE IBM ULTRIUM-TD3 57GA



Lun b TAPE IBM ULTRIUM-TD3 57GA



Lun c TAPE IBM ULTRIUM-TD3 57GA



Lun d TAPE IBM ULTRIUM-TD3 57GA



Lun e TAPE IBM ULTRIUM-TD3 57GA



Lun f TAPE IBM ULTRIUM-TD3 57GA



Lun 10 TAPE IBM ULTRIUM-TD3 57GA





Device PortId 103ef DeviceId 1 WWPN 100000068d02fd00

Lun 0 CHANGER ATL P1000 R138



Lun 1 TAPE IBM ULTRIUM-TD2 R138



Lun 2 TAPE IBM ULTRIUM-TD2 R138



Lun 3 TAPE IBM ULTRIUM-TD2 R138



Lun 4 TAPE IBM ULTRIUM-TD2 R138



Lun 5 TAPE IBM ULTRIUM-TD2 R138



Lun 6 TAPE IBM ULTRIUM-TD2 R138


[root@bkp101:/kernel/drv]# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t0d0 CD-ROM connected configured unknown
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
c1::dsk/c1t1d0 disk connected configured unknown
c1::dsk/c1t2d0 disk connected configured unknown
c1::dsk/c1t3d0 disk connected configured unknown
c1::lus4 disk connected configured unknown
c2 scsi-bus connected configured unknown
c2::lus0 unknown connected configured unknown
c3 scsi-bus connected configured unknown
c3::lus1 unknown connected configured unknown
c4 scsi-bus connected configured unknown
c4::lus2 unknown connected configured unknown
c5 scsi-bus connected configured unknown
c5::lus3 unknown connected configured unknown
c6 scsi-bus connected configured unknown
c6::lus5 unknown connected configured unknown
c7 fc-fabric connected configured unknown
c7::100000068d02fd00 med-changer connected configured unknown
c7::100000068d041100 med-changer connected configured unknown
c8 fc connected unconfigured unknown
usb0/1 unknown empty unconfigured ok
usb0/2 unknown empty unconfigured ok
usb1/1 unknown empty unconfigured ok
usb1/2 unknown empty unconfigured ok

[root@bkp101:/kernel/drv]# cfgadm -al -o show_FCP_dev c7::100000068d041100
Ap_Id Type Receptacle Occupant Condition
c7::100000068d041100,0 med-changer connected configured unknown
c7::100000068d041100,1 tape connected configured unknown
c7::100000068d041100,2 tape connected configured unknown
c7::100000068d041100,3 tape connected configured unknown
c7::100000068d041100,4 tape connected configured unknown
c7::100000068d041100,5 tape connected configured unknown
c7::100000068d041100,6 tape connected configured unknown
c7::100000068d041100,7 tape connected configured unknown
c7::100000068d041100,8 tape connected configured unknown
c7::100000068d041100,9 tape connected configured unknown
c7::100000068d041100,10 tape connected configured unknown
c7::100000068d041100,11 tape connected configured unknown
c7::100000068d041100,12 tape connected configured unknown
c7::100000068d041100,13 tape connected configured unknown
c7::100000068d041100,14 tape connected configured unknown
c7::100000068d041100,15 tape connected configured unknown
c7::100000068d041100,16 tape connected configured unknown


[root@bkp101:/kernel/drv]# inquire -v
scsidev@0.100.0:ATL P1000 R138|Autochanger (Jukebox)
S/N: SG03060000
ATNN:ATL P1000 SG03060000
scsidev@6.0.0:CSC 73GB10K REFURBISHED 0125|Disk, /dev/rdsk/c1t0d0s2
S/N:
scsidev@6.1.0:CSC 73GB10K REFURBISHED 0125|Disk, /dev/rdsk/c1t1d0s2
S/N:
scsidev@6.2.0:SEAGATE ST373307LSUN72G 0507|Disk, /dev/rdsk/c1t2d0s2
S/N: 3HZ9BBMB00007513CDCB
scsidev@6.3.0:HP 73.4GST373405LC HP03|Disk, /dev/rdsk/c1t3d0s2
S/N: 3EK1YXWP
ATNN:SEAGATE ST373405LC 3EK1YXWP
IENN:0004CFFFFEAA6C38


[root@bkp101:/kernel/drv]# jbconfig
1) Configure an AlphaStor/SmartMedia Jukebox.
2) Configure an Autodetected SCSI Jukebox.
3) Configure an Autodetected NDMP SCSI Jukebox.
4) Configure an SJI Jukebox.
5) Configure an STL Silo.

What kind of Jukebox are you configuring? [1] 2

All the Jukeboxes that are connected are already configured.
No new jukeboxes are found on host bkp101.

 

[605]

This is not a NW issue so far as NW only can use what the OS has configured. As long as this has not been solved, do not try to configure a NW jukebox which he cannot see with inquire.

 

[terrywashington]

OK. Thanks for the info.

 

[terrywashington]

EMC had me add the below entry with the WWN of the new Sepaton unit to /usr/kernel/drv/lus.conf and do a reconfiguration reboot. The unit was then visible in inquire output and I was able to add it via jbconfig.

name="lus" parent="fp" target=50 lun=0 fc-port-wwn="100000068d041100";

 

[605]

Well done. Thanks for sharing the results.