ISDN ETSI from LUCENT Definity 1

[jforti]

Folks,

I have a solution with a Switch from Marconi with a link E-1 ISDN ETSI, it is connected to the Definity. The equipment are not in communication, because the Definity send any bits, such as 030200000F0101C01803A98386 instead of 08..., 08.. is the standard of ETSI. Does anybody know what mean 03... is ?

Thanks in advance

Juliano F.

 

[fastbusy]

Hi there - I've pasted the working Definity config of a simple ESTI E1 circuit as used here in the UK - Hope it helps. Apologies for the formatting - I suggest you paste into an app. to make sense of it.

Regards,

G.




change ds1 01a16 Page 1 of 1
DS1 CIRCUIT PACK

Location: 01A16 Name: BT ISDN30E
Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri
Connect: network
Country Protocol: etsi
Protocol Version: b
Interface Companding: alaw CRC? n
Idle Code: 01010100
DCP/Analog Bearer Capability: 3.1kHz




Slip Detection? n Near-end CSU Type: other



change trunk-group 1 Page 1 of 10
TRUNK GROUP

Group Number: 1 Group Type: isdn CDR Reports: y
Group Name: BT 7000 DDI 01A16 COR: 50 TN: 1 TAC: 031
Direction: two-way Outgoing Display? n
Dial Access? y Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send TCM,Lookahead: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: c Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: cyclical
Connected to Toll? n STT Loss: normal DTT to DCO Loss: normal
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0

change trunk-group 1 Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member: 1
Send Name: n Send Calling Number: n
Used for DCS? n Send Connected Number: n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider






Send UCID? n
Send Codeset 6/7 LAI IE? y







change trunk-group 1 Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30

Port Code Sfx Name Night Sig Grp
1: g1A1601 TN464 F 8
2: 01A1602 TN464 F 8
3: 01A1603 TN464 F 8
4: 01A1604 TN464 F 8
5: 01A1605 TN464 F 8
6: 01A1606 TN464 F 8
7: 01A1607 TN464 F 8
8: 01A1608 TN464 F 8
9: 01A1609 TN464 F 8
10: 01A1610 TN464 F 8
11: 01A1611 TN464 F 8
12: 01A1612 TN464 F 8
13: 01A1613 TN464 F 8
14: 01A1614 TN464 F 8
15: 01A1615 TN464 F 8


change trunk-group 1 Page 5 of 10
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30

Port Code Sfx Name Night Sig Grp
16: 01A1617 TN464 F 8
17: 01A1618 TN464 F 8
18: 01A1619 TN464 F 8
19: 01A1620 TN464 F 8
20: 01A1621 TN464 F 8
21: 01A1622 TN464 F 8
22: 01A1623 TN464 F 8
23: 01A1624 TN464 F 8
24: 01A1625 TN464 F 8
25: 01A1626 TN464 F 8
26: 01A1627 TN464 F 8
27: 01A1628 TN464 F 8
28: 01A1629 TN464 F 8
29: 01A1630 TN464 F 8
30: 01A1631 TN464 F 8

 

[jforti]

fastbusy,

Thank you very much for your help.
Could you help me again ?
In the display on the POTS digital, they are receiving the following format : Call from 9202, for example. (9202 is extension line)
When the PBXs are connected back-to-back, the POTS receive JULIANO 9202, how can I change in the PBX to the POTS receive the name and number correctly?
It happens because I have a voice compression system in the middle, and the people from voice compression system told me the PBX is using a proprietary signalling and does not standard ISDN, so the voice compression system can not understand the bits from PBX.

Thank you,

Juliano