Hello All,
I have a problem with packets going from my network thru the PIX to my vpn endpoint. If the PIX is off the network (just my verizon dsl modem, and a dlink switch using verizon pppoe dialup client) my safenet client connects to my endpoint fine. When the PIX is connected to the network (verizon dsl modem connected to PIX, the safenet client can't connect, I just get a message in the safenet log saying "message not recieved retransmitting".
The PIX information log has an entry stating:
305011:Built dynamic udp translation from inside:192.169.2.10/500 to outside:155.197.11.8:96
302015:Built outbound udp connection 61515 for outside:151.196.142.42/500 (155.197.142.42/500) to inside:192.169.2.10/500 (155.197.11.8/96)
My question why is the ip address of the PIX port 96 instead of 500 for IPSEC? I think this will solve my problem of the client not connecting to my dlink endpoint.
I need to have port 500 open along with protocol 50, and 51.
Does my config allow for this?
Encerything else works fine. I can connect to the PIX with the cisco vpn client, and split tunneling works. I can map drive, and use remote desktop for server maintenance
If I can get this safenet client to connect back with the dlink thru the PIX I will be in NERVANA!!
Any help is greatly appreciated
192.169.2.0 - lan
155.197.142.42 - dlink vpn endpoint
155.197.11.8 - PIX outside
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list inside_outbound_nat0_acl permit ip any 10.10.10.0 255.255.255.0
access-list OUTSIDE_IN permit icmp any any
access-list outside_cryptomap_dyn_10 permit ip any 10.10.10.0 255.255.255.0
access-list split permit ip 192.169.2.0 255.255.255.0 10.10.10.0 255.255.255.0
pager lines 24
logging on
icmp permit any outside
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 192.169.2.1 255.255.255.0
ip verify reverse-path interface outside
ip verify reverse-path interface inside
ip audit info action alarm
ip audit attack action alarm
ip local pool kgcpa 10.10.10.1-10.10.10.10
pdm location 192.169.2.0 255.255.255.0 inside
pdm location 10.10.10.0 255.255.255.0 inside
pdm location 192.169.2.0 255.255.255.255 inside
pdm location 10.10.10.0 255.255.255.255 inside
pdm location 10.10.10.0 255.255.255.0 outside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route inside 10.10.10.0 255.255.255.0 192.169.2.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.169.2.0 255.255.255.0 inside
http 10.10.10.0 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
sysopt connection permit-l2tp
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 10 match address outside_cryptomap_dyn_10
crypto dynamic-map outside_dyn_map 10 set pfs group2
crypto dynamic-map outside_dyn_map 10 set transform-set ESP-3DES-MD5
crypto dynamic-map outside_dyn_map 10 set security-association lifetime seconds 86400 kilobytes 4608000
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0 no-xauth no-config-mode
isakmp identity address
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup kgcpaipsec address-pool kgcpa
vpngroup kgcpaipsec dns-server 192.169.2.2
vpngroup kgcpaipsec default-domain ajinc.local
vpngroup kgcpaipsec split-tunnel split
vpngroup kgcpaipsec pfs
vpngroup kgcpaipsec idle-time 1800
vpngroup kgcpaipsec max-time 86400
vpngroup kgcpaipsec password ********
telnet timeout 5
ssh timeout 5
management-access inside
console timeout 0
vpdn group pppoe_group request dialout pppoe
vpdn group pppoe_group localname vze2q563
vpdn group pppoe_group ppp authentication pap
vpdn username vss3e565 password *********
dhcpd address 192.169.2.10-192.169.2.41 inside
dhcpd dns 192.169.2.2
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd domain ajinc.local
dhcpd auto_config outside
dhcpd enable inside
terminal width 80
I have a problem with packets going from my network thru the PIX to my vpn endpoint. If the PIX is off the network (just my verizon dsl modem, and a dlink switch using verizon pppoe dialup client) my safenet client connects to my endpoint fine. When the PIX is connected to the network (verizon dsl modem connected to PIX, the safenet client can't connect, I just get a message in the safenet log saying "message not recieved retransmitting".
The PIX information log has an entry stating:
305011:Built dynamic udp translation from inside:192.169.2.10/500 to outside:155.197.11.8:96
302015:Built outbound udp connection 61515 for outside:151.196.142.42/500 (155.197.142.42/500) to inside:192.169.2.10/500 (155.197.11.8/96)
My question why is the ip address of the PIX port 96 instead of 500 for IPSEC? I think this will solve my problem of the client not connecting to my dlink endpoint.
I need to have port 500 open along with protocol 50, and 51.
Does my config allow for this?
Encerything else works fine. I can connect to the PIX with the cisco vpn client, and split tunneling works. I can map drive, and use remote desktop for server maintenance
If I can get this safenet client to connect back with the dlink thru the PIX I will be in NERVANA!!
Any help is greatly appreciated
192.169.2.0 - lan
155.197.142.42 - dlink vpn endpoint
155.197.11.8 - PIX outside
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list inside_outbound_nat0_acl permit ip any 10.10.10.0 255.255.255.0
access-list OUTSIDE_IN permit icmp any any
access-list outside_cryptomap_dyn_10 permit ip any 10.10.10.0 255.255.255.0
access-list split permit ip 192.169.2.0 255.255.255.0 10.10.10.0 255.255.255.0
pager lines 24
logging on
icmp permit any outside
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 192.169.2.1 255.255.255.0
ip verify reverse-path interface outside
ip verify reverse-path interface inside
ip audit info action alarm
ip audit attack action alarm
ip local pool kgcpa 10.10.10.1-10.10.10.10
pdm location 192.169.2.0 255.255.255.0 inside
pdm location 10.10.10.0 255.255.255.0 inside
pdm location 192.169.2.0 255.255.255.255 inside
pdm location 10.10.10.0 255.255.255.255 inside
pdm location 10.10.10.0 255.255.255.0 outside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route inside 10.10.10.0 255.255.255.0 192.169.2.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.169.2.0 255.255.255.0 inside
http 10.10.10.0 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
sysopt connection permit-l2tp
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 10 match address outside_cryptomap_dyn_10
crypto dynamic-map outside_dyn_map 10 set pfs group2
crypto dynamic-map outside_dyn_map 10 set transform-set ESP-3DES-MD5
crypto dynamic-map outside_dyn_map 10 set security-association lifetime seconds 86400 kilobytes 4608000
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0 no-xauth no-config-mode
isakmp identity address
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup kgcpaipsec address-pool kgcpa
vpngroup kgcpaipsec dns-server 192.169.2.2
vpngroup kgcpaipsec default-domain ajinc.local
vpngroup kgcpaipsec split-tunnel split
vpngroup kgcpaipsec pfs
vpngroup kgcpaipsec idle-time 1800
vpngroup kgcpaipsec max-time 86400
vpngroup kgcpaipsec password ********
telnet timeout 5
ssh timeout 5
management-access inside
console timeout 0
vpdn group pppoe_group request dialout pppoe
vpdn group pppoe_group localname vze2q563
vpdn group pppoe_group ppp authentication pap
vpdn username vss3e565 password *********
dhcpd address 192.169.2.10-192.169.2.41 inside
dhcpd dns 192.169.2.2
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd domain ajinc.local
dhcpd auto_config outside
dhcpd enable inside
terminal width 80