soaressteevan
Technical User
Hey guys,
I have two systems (IPS) and (IPX) I was trying (since 3 days) to connect both systems using CCIS over IP.
In the IPS the steps are very clear but in the IPX it is very diffecult for me.
Can any body help me in the IPX side?
these are the programs I have done to IPS ( point code 1) (Ip address 192.168.1.36/24) stations numbering 2XX.
Note: th IPX is (point code 2) (IP address 192.168.1.2/24) stations numbering 4XX.
a) CM 050>32>38. Virtual FP 32
b) CM 054>32>12. Used PIM number 12
c) CM 056>32>0. Virtual IPT
d) CM 0607>0>32. IPT channel 0 to since wheel 32
e) CM 14>32000~32003>D100~D103. 4 trunks assigned
f) CM 3000>100~103>10. Put the trunks in route 10
g) CM 3500>10>04. Route number 10 is tie line
h) CM 3504>10>2. Answer signal arrives
i) CM 3509>10>03. Incoming connection signal is winkstart CCIS
j) CM 3520>10>00. Sender start condition is winkstart.
k) CM 3583>10>0. Trunk seizure sequence is lower first
l) CM 3590>10>0. special features enable
m) CM 3591>10>0. CCH no. 0 is used fpr CCIS IP trunk.
n) CM 3035>100~103>001~004. CIC for each trunk
nn) CM 200>4>A129. (LCR group 3 when dialing 4 (the IPX stations numbering plan 4XX)
o) CM 8AA000>3>4007. Area code development pattern 007 for LCR group 3
p) CM 8A4007>4>0000. Route pattern number 000 when u dial 4.
q) CM 8A0000>1>00010. first choice is LCR pattern 000 trunk route 10.
r) CM 8A5000>167>000. LCR pattern 000 leads to IP address pattern 000.
s) CM 8A5000>168>00002. Destination point code is 2
t) CM 5B01>00000>192168001002 (IP address pattern no. 000 leads to IP address no. 0 which is 192.168.1.2
u) CM 857>4>03. Site B station format is 4XX (3 digits)
v) CM A700>0>254. IPT trunk no. 254
w) CM A701>0>00001. Originating code is 1
ww) CM A710>0>14. 28 sec is the ACM signal waiting timer when originating calls via CCIS.
x) CM A8>00002>0. Destination point code of site B CCH 0.
y) CM A746>0>0. Connection method to IP trunk is point to multi point.
z) EC6>0>0 and Reset MP
The IPX system is only 1 PIM.
I have two systems (IPS) and (IPX) I was trying (since 3 days) to connect both systems using CCIS over IP.
In the IPS the steps are very clear but in the IPX it is very diffecult for me.
Can any body help me in the IPX side?
these are the programs I have done to IPS ( point code 1) (Ip address 192.168.1.36/24) stations numbering 2XX.
Note: th IPX is (point code 2) (IP address 192.168.1.2/24) stations numbering 4XX.
a) CM 050>32>38. Virtual FP 32
b) CM 054>32>12. Used PIM number 12
c) CM 056>32>0. Virtual IPT
d) CM 0607>0>32. IPT channel 0 to since wheel 32
e) CM 14>32000~32003>D100~D103. 4 trunks assigned
f) CM 3000>100~103>10. Put the trunks in route 10
g) CM 3500>10>04. Route number 10 is tie line
h) CM 3504>10>2. Answer signal arrives
i) CM 3509>10>03. Incoming connection signal is winkstart CCIS
j) CM 3520>10>00. Sender start condition is winkstart.
k) CM 3583>10>0. Trunk seizure sequence is lower first
l) CM 3590>10>0. special features enable
m) CM 3591>10>0. CCH no. 0 is used fpr CCIS IP trunk.
n) CM 3035>100~103>001~004. CIC for each trunk
nn) CM 200>4>A129. (LCR group 3 when dialing 4 (the IPX stations numbering plan 4XX)
o) CM 8AA000>3>4007. Area code development pattern 007 for LCR group 3
p) CM 8A4007>4>0000. Route pattern number 000 when u dial 4.
q) CM 8A0000>1>00010. first choice is LCR pattern 000 trunk route 10.
r) CM 8A5000>167>000. LCR pattern 000 leads to IP address pattern 000.
s) CM 8A5000>168>00002. Destination point code is 2
t) CM 5B01>00000>192168001002 (IP address pattern no. 000 leads to IP address no. 0 which is 192.168.1.2
u) CM 857>4>03. Site B station format is 4XX (3 digits)
v) CM A700>0>254. IPT trunk no. 254
w) CM A701>0>00001. Originating code is 1
ww) CM A710>0>14. 28 sec is the ACM signal waiting timer when originating calls via CCIS.
x) CM A8>00002>0. Destination point code of site B CCH 0.
y) CM A746>0>0. Connection method to IP trunk is point to multi point.
z) EC6>0>0 and Reset MP
The IPX system is only 1 PIM.