IP tv on cisco 877w 1

[sprelligosi]

I´m trying to connect to my local IP-TV. It uses 3 PVC
7/48, 7/50 and 7/51 i´ve been trying to bridge them to fastethernet 3. but i still get no signal. Any thoughts?

best regards: Mr. Gudnason


version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Rooney
!
boot-start-marker
boot-end-marker
!
no logging buffered
enable secret 5 $1$DGqS$qh1jyp11SjWe0wA0lOYy3/
!
aaa new-model
aaa local authentication attempts max-fail 3
!
!
!
!
aaa session-id common
!
quit
dot11 syslog
dot11 vlan-name WIRELESS vlan 1
!
dot11 ssid Cisco
vlan 1
authentication open
guest-mode
!
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.10
ip dhcp excluded-address 192.168.1.254
ip dhcp excluded-address 192.168.1.100
!
ip dhcp pool DHCP_LAUGIN
network 192.168.1.0 255.255.255.0
dns-server 212.30.200.199 212.30.200.200
default-router 192.168.1.254
domain-name mydomain.com
!
!
ip name-server 212.30.200.199
ip name-server 212.30.200.200
ip multicast-routing
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip igmp snooping vlan 3 immediate-leave
no ip igmp snooping
no ip igmp ssm-map query dns
!
multilink bundle-name authenticated
!
!
username XXXX privilege 15 password 0 XXXXX
!
!
archive
log config
hidekeys
!
!
!
bridge irb
!
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 8/48
pppoe-client dial-pool-number 1
!
!
interface ATM0.10 multipoint
description TV_SKJARINN
pvc 7/48
description PORTAL
!
pvc 7/50
description IGMP
!
pvc 7/51
description VIDEO
!
bridge-group 10
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
description TV SKJARINN
switchport access vlan 3
duplex half
speed 100
spanning-tree portfast
hold-queue 1024 in
hold-queue 1024 out
!
interface Dot11Radio0
no ip address
!
encryption vlan 1 key 1 size 40bit 0 XXXXXXX transmit-key
encryption vlan 1 mode wep mandatory
!
ssid Cisco
!
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Vlan1
no ip address
ip virtual-reassembly
ip tcp adjust-mss 1412
bridge-group 1
hold-queue 100 out
!
interface Vlan3
description TV VLAN
no ip address
ip pim sparse-mode
bridge-group 10
!
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username XXXXX password 0 XXXXX
!
interface BVI1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly
!
ip default-gateway 192.168.1.254
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list NAT_INNI interface Dialer0 overload
!
ip access-list standard NAT_INNI
permit 192.168.1.0 0.0.0.255
remark IP ADDRESSUR PRIVATE
!
dialer-list 1 protocol ip permit
!
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
bridge 10 protocol ieee
banner motd ^CHVAD ER I GANGI^C
!
line con 0
no modem enable
speed 115200
line aux 0
line vty 0 4
privilege level 15
transport input telnet ssh
!
scheduler max-task-time 5000
end

 

[burtsbees]

Wrong bridge group for vlan 310, supposed to be 1).

duplex on fa3 needs to be full.

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!