IP Office and Nokia Premicell

[timbath]

Can someone please help me with the shortcode to direct all 07* calls to a Premicell. I know I need to use the extension number, a D and a comma but I need a bit more help!

Thanks in advance.

 

[rickuk99]

I think I know what you mean, I take it the premicell is connected to an extension rather than a analouge truck, if the extension is say 300, your short code would be, 07n, number would be 300,,07n and set to dailextn. If you want to supress the number so you dont give out cli try number of 300,,14107n.

 

[timbath]

I thought it needed a "D".

 

[rickuk99]

I have used this and it works fine. The only problem is if one call is already in progress the second call will get and engaged tone as the extension is already busy.

 

[timbath]

I have tried it but it will not work.

I have the Nokia 22 connected to analogue extension 205. I can dial out by dialing 205 then the full destination number. I have also configured it to accept incoming calls and divert them to the main number. So I am confident that the Premicell works.

I have tried your shortcode but all I get is a ringing tone, the call is answered, there is a short silence then three short beeps, the mobile network unavailable tone.

 

[IPGuru]

From memory the short code should be
short code 07N
number 300d.
feature DialExt
300 could be either the premicell ext or a hunt group of premicells

 

[MichaelCullen]

Hi

I have tried all these short codes to get our premicell to work but I can't dial out

any ideas what else I could try

Thanks

Michael

 

[TheSecondComing]

If you have LCR try also having the shortcode in the LCR table. Also, ensure the Premicell is set to Ext mode and not Line mode.

 

[jpruffle]

Hi,

You need the following:

Create a user for example Premicell, ext number 301.

Create a shortcode with the following:

Shortcode = 07n
Telephone Number = 301D,07n (where 301 is the extension number)
Feature = DialExt

This will work as long as extension mode is selected on the premicell unit.

regards,

JPR

 

[MichaelCullen]

Hi

were not using LCR but I might try that aswell but I think that it is the line and ext mode

Thanks for the advice

Michael

 

[MichaelCullen]

Hi

we have a Ericsson F250m

does anyone know how to set this into ext mode

Thanks

 

[MrIPO]

I have only played with the Ericsson F220M, from what i can remember it was a automatic process.

 

[MichaelCullen]

ok

I tried the new short code

Shortcode = 07n
Telephone Number = 301D,07n (where 301 is the extension number)
Feature = DialExt

and it rings out but when the other end picks up the line gets dropped.

any ideas?

 

[mcsematt]

Hi, we have a handfull of premicells on our phone system, which were bought at separate times, and we have found that some didn't work. Having conversations with the supplier we found that a few had to go back as they had an early revision of the board in them, which requires more power over the line to make them pick-up than the IPO can provide, unlike some other systems and the phone company. So our supplier replaced the boards in the premicell and all seems to be working fine now.

 

[Retsilla]

Hi,

I have the IP Office 403 with PRI (ISDN30) plus an additional 30 port Analogue.

I have purchased 2 Ericsson F251m Fixed Cellular Terminals but can't get them to work with the PBX!! Arrrgh

If I connect a phone directly into the Premicell it works fine. I have looked through the other messages and have tried the short codes but it keeps coming up with the engaged tone as if the number isn't recognised.

I currently have the Permicells plugged into 2 ext numbers 220/222 and have tried them in a hunt group but still get the same problem.

Does anyone have any ideas how to set these up as Avaya don't want to know.

Many thanks

Allister

 

[IPGuru]

If you can connetc a phone into the premicell then it is emulatinmg a trunk
you will need to connect it to an atm

 

[Retsilla]

Hi IPGuru

I am a bit confused now. What is an atm?

 

[big70]

Analoog trunk module.

Greets Peter