Installing universal trunk card for paging 2

[Buster452]

The guy I was going to have install a universal trunk card in our Option 61c flaked out. So, I figured I might be able to tackle this on myself.

I can do moves/adds/changes and I've managed to stumble my way through a few other things on the switch.

The card is on it's way. I'll need to install it and setup a TN for paging over a Valcom V2006a.

Which manuals/sections of manuals should I be looking at (on helsman express)?

Does anyone have a step-by-step guide for this?

Thanks,
Buster

 

[johnpoole]

ldl 16 to add a route, ld 14 to add the trunks.. i can post a page route and trunk tomorrow. i don't use trunk type pag, i use cot so that i can adjust timer ftd,
force timed disconect. by setting that to 180, a paging trunk that hangs, only hangs for 3 minutes max. you'll need a vacant dn, and any slot in the ipe section of your 61

john poole
bellsouth business
columbia,sc

 

[chrisay59]

You could also just use an Analogue extension to dial the paging device, depends on what the Paging system is looking for, i.e Earth Loop Calling or DTMF.

 

[johnpoole]

the paging system interface is either trunk side of line side. some are switchable

john poole
bellsouth business
columbia,sc

 

[mluckie1]

The Valcom unit you specify will do a COT, loop or GRD start from the PBX, or a 2500 set. The instructions that came with the valcom should have the settings, DIP switches and connection points. To use COT do as John said, RDB in LD 16 and the trunk member in LD 14. If you are using the ACOD of the route to access page make sure that there is nothing in TARG, the default is 1 to remove it when you get to the TARG prompt enter X1.

 

[johnpoole]

here is the code i mentioned

TYPE RDB
CUST 00
ROUT 22
DES  PAGE
TKTP COT
NPID_TBL_NUM   0
PRIV NO
SAT  NO
IDEF NET
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
[b]ACOD 8222[/b]
CPP  NO
TARG 06
CLEN 1
OABS
TIMR ICF  512
     OGF  512
     EOD  13952
     DSI  34944
     NRD  10112
     DDL  70
     OOD  3
     ODT  4096
     RGV  640
     FLH  510
     GRD  896
     SFB  3
     CRD  512

     IENB  5 [COLOR=red]
     TFD   180 [/color]
     LEXT  100
     VGD  6
SST  3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR  NO
MUS  NO
MR   NO
RACD NO
MANO NO
EQAR NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0


PAGE 002

FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART  0
SGRP 0
AACR NO

note the tfd timer, keeps the page below 3 minutes and forces a disconect if the page trunk hangs. the acod is my page access code, the targ 6 is because all the patient phones are tgar 6, keeping the paging system from being used for a nurse call..

TYPE: cot
TN   32 0 0 1
DATE
PAGE

DES  PAGE
TN   032 0 00 01
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK  ANLG
NCOS 1
RTMB 22 1
NITE
SIGL LOP
SUPN NO
AST  NO
IAPG 0
CLS  UNR DTN WTA LPR APN THFD
     P10 NTC
TKID

90 percent of this is default, if you've never done a route and trunk before, take all the defaults it will let you. then go back and do a change on the few that are modified.


john poole
bellsouth business
columbia,sc

 

[Johnthephoneguy]

I just did this on an option 11 the other day, it takes less than 15 minutes from start to finish, and that includes the punchdowns. (I already had the pager input in place)

 

[johnpoole]

i agree, vendors seem to make it appear a lot harder then it is..

john poole
bellsouth business
columbia,sc

 

[Buster452]

OK, got the card (NT8D14BB)in last night. This morning I slid the card into slot 6.

I'm missing something though. When I dial the ACOD (7200) I get a fast busy and see "ERR404 0" on the terminal.

I tried clearing the "TARG" with x1, but it stayed 06. I then entered 1, and now it's shows 01 06.

Also, I punched it to the first pair of wires on the card (blue & white), but I read somewhere the wiring might be weird on these cards (density or something) but I didn't quite understand.

The Valcom unit is set to loop start. I tried gnd start but that didn't help.


Here's the programming on the switch;
-----
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 22

TYPE RDB
CUST 00
ROUT 22
DES PAGE
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 7200
CPP NO
TARG 06
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0


PAGE 002

SGRP 0
AACR NO
-----------------------
TN 028 0 06 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 1
RTMB 22 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD
P10 NTC LOL
TKID
DATE 2 SEP 2005
----

 

[mluckie1]

to remove the targ X1 and X6 at the targ prompt

 

[Buster452]

Ok, got the TARG cleared. Still nothing.

When I dial 7200, it's just dead air. It does nothing until I press any number key, then it pops that ERR404 0 on the console and the phone does a fast busy.

I had used this paging system before on a Lucent switch, and when you accessed it, you would get a tone that you then dial you zone to. This trunk/route doesn't seem to be making the connection to the Valcom V2006.

Buster

 

[Buster452]

Wow, my engrish weren't so goodly on that last sentence. Sorry, it should have read.

"I had used this paging system before on a Lucent Switch. When you dialed into it, the paging unit would answer and generate a tone. You could then dial the zone you wanted to page."

Buster

 

[mluckie1]

Check the dip switch setting on the Valcom. If you put a toner on the TN can you hear it when you dial the ACOD??

 

[mluckie1]

SW1 and SW2 DOWN, SW6 UP, SW3 1 UP Dialtone(away from Board), DOWN No DT, SW3 2 down, SW3 3 down. wht/blu pr to wht/blu pr of PBX. You should be able to put a Butt set on the Valcom pr and get Dialtone.

 

[Buster452]

Ok, bonehead move. I have gbix blocks and stradled two pairs of house feeds.

Now I'm getting the dialtone of the Valcom, but cannot send dtmf to choose the zone once the Valcom picks up.

I dial 7200, get the valcom dialtone, press a number and get fast busy, ERR404 0 pops up on the console.

Getting closer.

I'll pop over to that building and check the dip switches on the Valcom.

Thanks,
Buster

 

[mluckie1]

Make sure the set you are calling from has CLS UNR. Press # after ACOD then try again.

 

[Buster452]

Excellent!!! That was it. CLS UNR. It's working.

Ok, now I have to go add that to all phones.

Thanks a bunch!

Buster

 

[mluckie1]

Would be careful installing this cls to all phones. Make sure that the targ on on other RDB's match the sets tgar to avoid users accessing routes directly.