Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Installing new PRI with QCC- need LDNs?

Status
Not open for further replies.

refted

Vendor
Sep 12, 2008
31
US
I am installing a new PRI on Merlin Magix- DIDs are completely out of order- 4 main lines will come in and need to be sent to QCC consoles (2). How can I point them to the LDN? Do I need to renumber the LDN? Also on the PRI I am deleting 2 and adding 1 digit, but there is no where to 'add' the 1 that I need to add to make them match.


Any quick help is much appreciated!!!!
 
I think you'll find the answers in the FAQ section of this very group

Here's a direct link to the one that you want
 
Tommy,
Thanks for the help.

I did that to manipulate the DIDs. If I renumber an extension to 3108 it comes through, but if not it goes to the Oper (should go to x28).


A Slot 6 Switch: 5ESS

A System: By line

A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 1 6 CallbyCall By Dial Plan

A Channel ID: 23 22 21 20 19 18 17 16 15 14
A 13 12 11 10 9 8 7 6 5 4
A 3 2 1

A Line PhoneNumber NumberToSend
A 825 4109624436
A 826 4109624436
A 827 4109624436
A 828 4109624436
A 829 4109624436
A 830 4109624436
A 831 4109624436
A 832 4109624436
A 833 4109624436
A 834 4109624436
A 835 4109624436
A 836 4109624436
A 837 4109624436
A 838 4109624436
A 839 4109624436
A 840 4109624436
A 841 4109624436
A 842 4109624436
A 843 4109624436
A 844 4109624436
A 845 4109624436
A 846 4109624436
A 847 4109624436

A Network Selection Table

A Entry Number: 0 1 2 3
A Pattern to Match: 101**** 10***

A Special Service Table

A Entry Number: 0 1 2 3 4 5 6 7
A Pattern to Match: 011 010 01 00 0 1
A Operator: none OP OP OP/P OP none none none
A Type of Number: I I I N N N N N
A Digits to Delete: 0 0 0 0 0 0 0 0

A Call-By-Call Service Table

A Entry Number: 0 1 2 3 4
A Pattern 0: 0
A Pattern 1: 1
A PRI INFORMATION


A Pattern 2: 2
A Pattern 3: 3
A Pattern 4: 4
A Pattern 5: 5
A Pattern 6: 6
A Pattern 7: 7
A Pattern 8: 8
A Pattern 9: 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ: No Service
A DeleteDigits: 0 0 0 0 0

A Entry Number: 5 6 7 8 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0

A Dial Plan Routing Table

A Entry Number: 0 1 2 3
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 4 4 0 0
A Pattern to Match: 3108
A Digits to Delete: 4 0 0 0
A Digits to Add: 3108 28

A Entry Number: 4 5 6 7
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 8 9 10 11
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 12 13 14 15
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

 
 http://files.engineering.com/getfile.aspx?folder=6e9d26ff-ec55-4f8a-804c-aa6d22667aec&file=PRI9.TXT
Your table 0 looks fine, are you sure that the telco is sending 4 digits, and that they are 3108?
Is this the only number coming in?


Your table expects to receive 4 digits, and if it gets 3108 it removes them entirely and replaces them with 28
 
It turns out that Telco SAID they were sending 3110 on the new test number; in fact they were sending 0311, so if I numbered my set to 311 or 3110 it would land there, but if I said expect 4, 3110, strip 4 and add 28 it would not work. I proved what they were sending with the Monitor tool.

Thanks for all who replied.
 
That's the first thing to check when calls start going to the operator like that. Had a trashy AT&T circuit once that would send a star with the digits sometimes and since the Merlin didn't see a route like that it would send the call to the operator. I went round and round with them until they finally sent a tech out with a Tberd and we saw the star come in randomly.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top