Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Installation of AACC 6.2 SP4 with CS1K on AML, Services Problem when switchover

Status
Not open for further replies.

superdigi

Technical User
Apr 16, 2012
11
i have a problem when i do the switchover from ccms active server to ccms standby server. when i restart the server for active server System control and monitor utility(SCMU) checked all the services all started. the problem is occur are when do the switchover, SCMU checked ASM_service,TFE_service and VSM_service are starting.i wait for 30min also unable to start the service. in the same time, i go to services.msc check that 3 service are state as started. this all are very weird. the status for pabx are as below when this 3 service are not started.hope you all can be help me on this problem.


SERVER TASK: ENABLED
ELAN #: 017 Des: AACC6.2
APPL_IP_ID: 0. 0. 0. 0 LYR7: Active application:disable
 
May I know how you are initiating the switchover ?
What are the status messages appearing on the High Availability Tool ?
 
hi,
i go to high availability--> system control--> at the control drop down box select switchover and then click ok.
after that my active server SCMU services will stop and my standby server services will automatic start back.

at the system configuration information will show the message as below.

Time Jul 16 : 6:46 PM : Stop the Shadowing Process.
Standby Mode Server is actively Shadowing data.
Shadowing has been suspended. To continue, please Stop Shadowing, ensure that the Active Mode Server is available and start Shadowing to continue.
Shadowing is stopped.
Active Mode Server configured has the Shadowing Service Enabled. Standby Configured Server can Shadow data.
Active Mode Server cannot Shadow data.
The Standby Mode Server configured is not shadowing this Active Mode Server.There are no Shadow Client Server(s) shadowing this Active Mode Server.
Time Jul 16 : 6:50 PM : Standby Mode Server is actively shadowing data.
Stop the Shadowing Process.Active Mode Server cannot Shadow data.
 

During switch over , whether the managed IP is released from Active and taken by Standby ?
 

Please ensure you followed the guideline for choosing managed IPs as per Avaya RU3 release notes:

Choosing Managed IP addresses
For AML HA, SIP RnR, the Managed IP should be lower than the Active and Standby Physical IP addresses
Active: 10.0.0.20
Standby: 10.0.0.30
Managed: 10.0.0.10

For Mission Critical HA, the Managed IP should be higher than the Active and Standby Physical IP addresses
Active: 10.0.0.10
Standby: 10.0.0.20
Managed: 10.0.0.30

Document :AACC6.2_Release_Notes_SP5_RU1_RU2_AND_RU3.pdf
Version :8.5 (released on July 6 , 2012)
 
Hi Apds,

the manage IP address cant be taken from active to standby server.i tried the solution that you mention also doesn't work. currently my aacc6.2 is service pack 4, the HA can work for switchover function? some more i checked our PABX cs1000 version is 4.5 .
 
Not sure how you were sold AACC 6.2 if your pbx is on release 4.5, minimum supported release is 5.0......
 
on our lab just have CS1k 4.5 only . we just do a testing on our lab.
 
I have a similiar problem with the switchover from AACC 6.2 SP5 ELAN connected to CS1K rls.5.5.After the first switchover from Standby to Active, the ELAN will connect, but say APPLICATION DISABLED. We were told it is an compatibility issue with 5.5 with the workaround being to Shutdown and restart CCMS, server reboot not needed. When the services come back up the ELAN will connect and show Application Active. In performing this process TFE service takes forever to start, but usually does. The last time I did this after installing microsoft hotfixes on the servers, TFE would never start and I ended up having REM out all script references in the Master Script to take the load off of the OAM & TFE services. TFE started immediately afterwards. I then had to add back in the script references to the Master Script and reactivate each script, which is a slow process depending on script load. This is a prod system, not a lab system so script load may not be an issue.
 
The AACC is not supported with 4.5, doesn't matter if it's a lab system. If your trying this failover in the lab and it's not working it's because your connecting to a 4.5 switch....you need to upgrade your lab switch to a support version.

Cheers.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top