I1140E IP Set

[dcross]

I have set-up I1140 IP Set so I can login into it from other IP sets by entering the ext. and the SCPW 123. The Display of the set Local Mode (Thats Cool) but two lines Below that it shows Invalid ID (3) any Ideas?

DES 5597IP
TN 252 0 15 22 VIRTUAL
TYPE I2004
CDEN 8D
CTYP XDLC
CUST 0
NUID 5597
NHTN 252 0 15 22
ZONE 002
FDN 1700
TGAR 0
LDN NO
NCOS 7
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
SCPW 123
CLS UNR FBD WTA LPR MTA FNA HTA TDD HFA CRPA
MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDA CDMD LLCN MCTD CLBD AUTU
GPUA DPUD DNDA CFXA ARHA FITD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
DRDD EXR0
USMD USRD ULAD RTDD RBDD RBHD PGND FLXD FTTC DNDY DNO3 MCBN
VOLA VOUD CDMR ICRD MCDD T87A KEM2
CPND_LANG ENG
RCO 0
HUNT 1700
LHK 1
PLEV 02
CSDN
AST 00
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 5597 0 MARP
CPND
NAME Don Cross
XPLN 9
DISPLAY_FMT FIRST,LAST
01 SCR 6497 D MARP
CPND
NAME Donald Cross
XPLN 12
DISPLAY_FMT FIRST,LAST
02 ADL 16
03 MCK
04 ADL 16
05 ADL 16
06 ADL 16
07 ADL 16
08 ADL 16
09 ADL 16
10 ADL 16
11 ADL 16
12
13
14
15
16 MWK 1700
17 TRN
18 AO6
19 CFW 16 96608084
20 RGA
21 PRK
22
23
24
25
26 CPN
27
28
29
30
31
DATE 23 OCT 2007

 

[johnpoole]

that a good one, are your other ip sets on the same zone?

john poole
bellsouth business
columbia,sc

 

[911guru]

Ok, 2 things stand out to me here.


1.) You say it says "LOCAL MODE". This tells me that the system is a Branch Office Telephone that is not registered to the main for some reason. Either it was forced into this mode for testing or the BUID is not registering to the Main. Most likely it was not able to be redirected to the main due to a BUID error locally or at the main, or in the NRS programming.

2.) The invalid ID (3). Not sure when you are getting that, in normal mode, or after you try to do a VO login. If it is just sitting there, then I suspect the BUID issue above. If it is being displayed after you try to do a VO login, it means that the ID you tried to use was not a valid one. This could be because the digits you entered were unable to be resolved locally or by the NRS, or some other reason outside of your local system.

Seems you have a deeper problem here than just the Virtual Office failing, IMHO.


911Guru

http://pbx-e911.com

 

[scottydont]

Hi dcross,

I think the guru is on the money. I have a site that does the same invalid id problem, even though it is registered back to the main site. It usually goes away after you go off-hook and hang up for the first time. I think it has somthing to do with the temporary registration password on the sig server "nodePwdSet". In the class maybe set "voua" on the local and main site sets and check to make sure the sig servers at both main and branch have been patched. I have found some engineers patch the PABX, but forget to patch the sig, so that may be worth checking.

Cheers

Scott