Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

HSRP problem

Status
Not open for further replies.

superduperlopez

Technical User
Mar 21, 2006
32
GB
I have two 837s running HSRP. Both routers are connected to a 2960.

Router_1:
interface Ethernet0
ip address 192.168.0.2 255.255.255.0
no ip redirects
standby 1 ip 192.168.0.1
standby 1 timers 254 255
standby 1 priority 111
standby 1 preempt
hold-queue 100 out

Router_2:
interface Ethernet0
ip address 192.168.0.3 255.255.255.0
no ip redirects
standby 1 ip 192.168.0.1
standby 1 timers 254 255
standby 1 priority 222
standby 1 preempt
hold-queue 100 out

I have noticed the following:
A) when I ping from Router_2 to the Switch all the packets come back fine BESIDES when I the Router is receiving HSRP messages. This is causing the Router loose one packet and that is why I have modified the Standby timer to send as little as possilbe...i.e.

Router_2#ping 192.168.0.4

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.4, timeout is 2 seconds:

*Apr 4 22:49:18.774: HSRP: Et0 Grp 1 Hello out 192.168.0.3 Active pri 222 vIP 192.168.0.1
*Apr 4 22:49:19.790: HSRP: Et0 Grp 1 Hello in 192.168.0.2 Standby pri 111 vIP 192.168.0.1.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
_______________________________________
The same happens when this message is received, but I don't quite understand what the message is about
Router_2#ping 192.168.0.4

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.4, timeout is 2 seconds:

*Apr 4 22:49:08.338: HSRP: Et0 REDIRECT adv in, Passive, active 0, passive 1, from 192.168.0.2.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/4 ms
____________________________________
in both cases I don't understand why these messages are affecting my pinging???

B) when I ping from the Switch to the virtual ip address the results are totally random...
Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/8 ms

Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
....!
Success rate is 20 percent (1/5), round-trip min/avg/max = 1/1/1 ms
Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/8 ms
Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
....!
Success rate is 20 percent (1/5), round-trip min/avg/max = 1/1/1 ms
Switch#ping 192.168.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:

01:04:31: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending
01:04:31: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending full packet.
01:04:33: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending
01:04:33: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending full packet.
01:04:35: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending
01:04:35: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending full packet.
01:04:37: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending
01:04:37: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending full packet.!
Success rate is 20 percent (1/5), round-trip min/avg/max = 1/1/1 ms
01:04:39: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending
01:04:39: IP: s=192.168.0.4 (local), d=192.168.0.1 (Vlan1), len 100, sending full packet
01:04:39: IP: s=192.168.0.1 (Vlan1), d=192.168.0.4, len 100, rcvd 1

any ideas on what is happening???

thank you


 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top