How to set up two separate NIGHT Schedules

[pecossunset]

This system is a MICS 6.1 with a PRI in service.

I have a schedule that is being used for the DN 2300 CCR-AA:
MON-FRI
STOP 9am
LUNCH 12pm-1pm
START 4PM
SAT-SUN All Day

They want the school office which is a separate DN 2323 to have it's own seperate schedule:
MON-FRI
STOP 8am
( NO LUNCH )
START 3PM
SAT-SUN All Day

Is this possible to have two separate time schedules for two DN's? I can't figure out how to do this properly.

 

[Multimedium]

There can't be more than one schedule active on the system. However, here is something you can do:

Schedule 1: Starts at 4 PM, stops at 8 AM (for all DNs)
Schedule 2: Starts at 8 AM, stops at 9 AM (for DN 2300)
Schedule 3: Starts at 12 PM, stops at 1 PM (for DN 2300)
Schedule 4: Starts at 3 PM, stops at 4 PM (for DN 2323)

Would that work for you?

 

[pecossunset]

Yes thank you that should work.

It has been a while since I programmed schedules and the only FAQ is for a MANUAL schedule ( strange that there is not an AUTOMATIC schedule in FAQ it would helpful if that could be posted in FAQ ) anyway could you please refresh my memory on how to add this line which is Target line 180 to the schedule?

Thank you

 

[curlycord]

Services/RingingService/ShedNight/ change MANUAL to AUTO, press next untill you see Line Settings.
As for Times find them in Services/Common Settings/SheduledTimes



=----(((((((((()----=
curlycord

http://www.curlycord.com

Toronto Canada

http://www.telcopc.ca

 

[pecossunset]

Yes I found that but then what do I do next. I need to activate the AA CCR for both line 157 and line 180. It just says "Ring group 001

 

[Multimedium]

Then, you have to create Ringing Groups to go with your schedules. From what I understand, you would only need 2 Ringing Groups:
[ul]
[li]Ringing Group 001: DN 2300 assigned (to have the AA CCR answer immediately)[/li]
[li]Ringing Group 002: No DN assigned (to have the equivalent of Normal mode)[/li]
[/ul]

Finally, for each schedule, you have to assign a Ringing Group to the lines:
[ul]
[li]Schedule 1: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 001 (AA CCR)[/li]
[/ul][/li]
[li]Schedule 2: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 002 (Normal)[/li]
[/ul][/li]
[li]Schedule 3: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 002 (Normal)[/li]
[/ul][/li]
[li]Schedule 4: [ul]
[li]Line 157: Ringing Group 002 (Normal)[/li]
[li]Line 180: Ringing Group 001 (AA CCR)[/li]
[/ul][/li]
[/ul]

 

[Multimedium]

Then, you have to create Ringing Groups to go with your schedules. From what I understand, you would only need 2 Ringing Groups:
[ul]
[li]Ringing Group 001: DN 2300 assigned (to have the AA CCR answer immediately)[/li]
[li]Ringing Group 002: No DN assigned (to have the equivalent of Normal mode)[/li]
[/ul]

Finally, for each schedule, you have to assign a Ringing Group to the lines:
[ul]
[li]Schedule 1: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 001 (AA CCR)[/li]
[/ul][/li]
[li]Schedule 2: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 002 (Normal)[/li]
[/ul][/li]
[li]Schedule 3: [ul]
[li]Line 157: Ringing Group 001 (AA CCR)[/li]
[li]Line 180: Ringing Group 002 (Normal)[/li]
[/ul][/li]
[li]Schedule 4: [ul]
[li]Line 157: Ringing Group 002 (Normal)[/li]
[li]Line 180: Ringing Group 001 (AA CCR)[/li]
[/ul][/li]
[/ul]