How to program LIP - IP phones (LIP24/7024 etc) in IpLD-24/100/300

[doktor]

Follow these steps to install an IP phone in ipLDK-100:

The needed hardware is VOIB or VOIBE.
For the VOIB, VOIU channel boards are needed. Each VOIU gives 2 VoIP channels. Maxinum 8 VoIP channels per VOIB.

For the VOIBE, VOIUE channel boards are needed. Each VOIU gives 12 VoIP channels. Maxinum 24 VoIP channels per VOIBE.


Only LG-Nortel H.323 IP phones can be used.
Licenses are not needed with hard phones, just with soft phones.

Programming. Follow these steps for success...

* In PGM 101 and PGM 103 the VOIB/VOIBE should be installed in a proper SLOT.

Now the IP address data for the VOIB/VOIBE should be set:

* In PGM 340 index #1: Here is the IP address for VOIB/VOIBE board set.
* In PGM 340 index #2: Here is the default gateway IP address set. This field must be set.
* In PGM 340 index #3: Here is the subnet mask for the VOIB/VOIBE board set.
* In PGM 340 index #5: Here is the trace password for VOIB/VOIBE board set. Set to 00000000
* In PGM 340 index #6: Here is the default codec for VOIB/VOIBE board set. Set to G.711 or G.723 or ?.
* In PGM 340 index #7: Default gain = 31.
* In PGM 340 index #8: No delay is wanted. TOS = type of service. ON is chosen.
* In PGM 340 index #9: Normal throughput is requested. TOS = type of service. High is chosen.
PGM 340 index 10: Normal reliability is requested. TOS = type of service. High is chosen.

Programming of the IP phones:

* In PGM 380 "VOIB Slot for RSG/IP Phone" you enter the SLOT number for the VOIB/VOIBE.
* In PGM 380 "RSG/IP Channel Number for IP Phone" you enter 1-8 (1-24)dependent of how many channels on the VOIB/(VOIBE) board, you need for IP - phones (speech channels).

* In PGM381 RSG/IP Number Assign. --- IP Phone Number.
Here the number of IP phones is entered.

To install the IP phone, the IP phones MAC adressen should be entered. This is done in:
PGM386 IP Phone Attribute -- > Set Mac Address

The MAC address is seen on the label on the IP phone.

Hereafter the IP phone (e.g. LIP-24 or LIP-70xx) is registered, as written in the manual for these phones.
Up to 64 IP phones can be registered within one ipLDK-100.
Good luck.
///doktor

///doktor

 

[doktor]

Here is my "way" install an IP phone:
(In this example the LIP-24 IP Phone is used, but this wil work with any other LG-Nortel IP phone):
----------------------------------------------------

LIP-24 is connected to a WAN IP address.

LIP-24 will write the following in the display when the power is connected:

NO RESPONSE FROM MFIM [L]
SET [*] - Retry [#]

Key *
MODE setting.
Put LIP-24 REMOTE
Enter the volume down arrow.

The following addresses and parameters shown in the accompanying agreement papers.

PHONE IP ADDRESS (DOT: *)
Enter here the IP address of LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
IP address must be entered manually, because it can not be assigned through DHCP.
Remember to press SAVE after each input.
Enter the volume down arrow.

PHONE NET MASK (DOT: *)
Here, enter the subnet mask for LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

ROUTER IP ADDRESS (DOT: *).
Here, enter the default gateway for the LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

LIP-24 then ask about:
SAME WITH MFIM LAN?
Set this to NO. Default is to YES.
Remember to press the SAVE button after typing in each entry. Enter the volume down arrow.

MFIM IP ADDRESS (DOT: *)
Here enter the IP address for the ipLDK-60 (VOIB) must be entered.
Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

There are additional items that can be set as needed:
INPUT DEVICE NUMBER
DHCP (Disabled) (not used in appliances in the LOCAL mode).

VLAN CONFIGURATION (If telephony data to travel in separate VLAN specified number here. VLAN number is entered, according to data in agreement papers).

WEB PASSWORD this is not optional.

Then restart the LIP phone.

If registraion fails, you might have forgotten to enter the MAC address of the IP Phone in PGM286.


///doktor

 

[tarikkk]

Hi doktor,

How can we change the IP adress of the LIP 7016D, I think it's not the same as on LIP24??
How can we get to the LIP 7016D menu??

Thanks for all these infos

Regards

 

[doktor]

Just go to the menu: PHONE IP ADDRESS (DOT: *) menu and change it accordingly.
The LIP-24, the LIP-7024 and LIP-7016 are programmed in the same way.
Let me know if you find differences...

///doktor

 

[tarikkk]

I'm sorry but I don't understand,
When I go to menu of the IP phone, I have only the same menu on a digital phone.
If you mean by menu, after the startup of te phone, here I have this:

NO RESPONSE FROM MFIM [L]
SET [*] - Retry [#]

But when I press * , I have

ENTER PASSWORD

And I have no password.

Same problem when I try to get to the phone parameter through a browser (browse phone IP adress) it asks for a password.

Any idea

 

[morenot]

Password is: 147*

 

[tarikkk]

OK thanks a lot morenot
I'll try this tomorow

 

[tarikkk]

OK
It works perfectly on the phone now I can use any adressing plan I want!!

But why did this password doesn't work on the browser page of the phone is it another one??

 

[doktor]

147* is the build-in password. Browser password is not set default.

///doktor

 

[tarikkk]

How come it's not set
I Used a new phone And I couln't get in it asks for password
I've tried everything usual: admin, root, 0000, no way to get in