-
1
- #1
Follow these steps to install an IP phone in ipLDK-100:
The needed hardware is VOIB or VOIBE.
For the VOIB, VOIU channel boards are needed. Each VOIU gives 2 VoIP channels. Maxinum 8 VoIP channels per VOIB.
For the VOIBE, VOIUE channel boards are needed. Each VOIU gives 12 VoIP channels. Maxinum 24 VoIP channels per VOIBE.
Only LG-Nortel H.323 IP phones can be used.
Licenses are not needed with hard phones, just with soft phones.
Programming. Follow these steps for success...
* In PGM 101 and PGM 103 the VOIB/VOIBE should be installed in a proper SLOT.
Now the IP address data for the VOIB/VOIBE should be set:
* In PGM 340 index #1: Here is the IP address for VOIB/VOIBE board set.
* In PGM 340 index #2: Here is the default gateway IP address set. This field must be set.
* In PGM 340 index #3: Here is the subnet mask for the VOIB/VOIBE board set.
* In PGM 340 index #5: Here is the trace password for VOIB/VOIBE board set. Set to 00000000
* In PGM 340 index #6: Here is the default codec for VOIB/VOIBE board set. Set to G.711 or G.723 or ?.
* In PGM 340 index #7: Default gain = 31.
* In PGM 340 index #8: No delay is wanted. TOS = type of service. ON is chosen.
* In PGM 340 index #9: Normal throughput is requested. TOS = type of service. High is chosen.
PGM 340 index 10: Normal reliability is requested. TOS = type of service. High is chosen.
Programming of the IP phones:
* In PGM 380 “VOIB Slot for RSG/IP Phone” you enter the SLOT number for the VOIB/VOIBE.
* In PGM 380 ”RSG/IP Channel Number for IP Phone” you enter 1-8 (1-24)dependent of how many channels on the VOIB/(VOIBE) board, you need for IP - phones (speech channels).
* In PGM381 RSG/IP Number Assign. --- IP Phone Number.
Here the number of IP phones is entered.
To install the IP phone, the IP phones MAC adressen should be entered. This is done in:
PGM386 IP Phone Attribute -- > Set Mac Address
The MAC address is seen on the label on the IP phone.
Hereafter the IP phone (e.g. LIP-24 or LIP-70xx) is registered, as written in the manual for these phones.
Up to 64 IP phones can be registered within one ipLDK-100.
Good luck.
///doktor
The needed hardware is VOIB or VOIBE.
For the VOIB, VOIU channel boards are needed. Each VOIU gives 2 VoIP channels. Maxinum 8 VoIP channels per VOIB.
For the VOIBE, VOIUE channel boards are needed. Each VOIU gives 12 VoIP channels. Maxinum 24 VoIP channels per VOIBE.
Only LG-Nortel H.323 IP phones can be used.
Licenses are not needed with hard phones, just with soft phones.
Programming. Follow these steps for success...
* In PGM 101 and PGM 103 the VOIB/VOIBE should be installed in a proper SLOT.
Now the IP address data for the VOIB/VOIBE should be set:
* In PGM 340 index #1: Here is the IP address for VOIB/VOIBE board set.
* In PGM 340 index #2: Here is the default gateway IP address set. This field must be set.
* In PGM 340 index #3: Here is the subnet mask for the VOIB/VOIBE board set.
* In PGM 340 index #5: Here is the trace password for VOIB/VOIBE board set. Set to 00000000
* In PGM 340 index #6: Here is the default codec for VOIB/VOIBE board set. Set to G.711 or G.723 or ?.
* In PGM 340 index #7: Default gain = 31.
* In PGM 340 index #8: No delay is wanted. TOS = type of service. ON is chosen.
* In PGM 340 index #9: Normal throughput is requested. TOS = type of service. High is chosen.
PGM 340 index 10: Normal reliability is requested. TOS = type of service. High is chosen.
Programming of the IP phones:
* In PGM 380 “VOIB Slot for RSG/IP Phone” you enter the SLOT number for the VOIB/VOIBE.
* In PGM 380 ”RSG/IP Channel Number for IP Phone” you enter 1-8 (1-24)dependent of how many channels on the VOIB/(VOIBE) board, you need for IP - phones (speech channels).
* In PGM381 RSG/IP Number Assign. --- IP Phone Number.
Here the number of IP phones is entered.
To install the IP phone, the IP phones MAC adressen should be entered. This is done in:
PGM386 IP Phone Attribute -- > Set Mac Address
The MAC address is seen on the label on the IP phone.
Hereafter the IP phone (e.g. LIP-24 or LIP-70xx) is registered, as written in the manual for these phones.
Up to 64 IP phones can be registered within one ipLDK-100.
Good luck.
///doktor