Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
how to make my report have picture backround 1
- Thread starter bantakiah
- Start date
- Thread starter
- #4
It would help if you describe exactly what you did and exactly what you are seeing now. "my detail is still white" is a bit vague.
- Ido
view, e-mail, export, burst, distribute, and schedule Crystal Reports.
- Ido
view, e-mail, export, burst, distribute, and schedule Crystal Reports.
- Thread starter
- #6
for default crystal report the paper is blank (do notr have background . i have do like lbass say but it only work on page header only. i want my backround is not blank anymore but all my background change with one picture. sorry for my bad english
- Thread starter
- #8
synapsevampire
Programmer
Place your mouse on the lower bar of the page header, click and hold as you pull down.
-k
-k
- Thread starter
- #10
synapsevampire
Programmer
No, you can do it any time.
And it doesn't matter if the other sections move down, it doesn't change their size.
What would you expect to happen to those sections below, that they remain where they are? You need to be a bit bolder and try what is suggested and if there are problems, state what they are, your questions are those of someone unwilling to test, so you'll never get anything done.
You do need to run the report before you'll see the results, so in that respect you'll need to connect to the database first, which is always the case with Crystal, you need data to display a report.
-k
And it doesn't matter if the other sections move down, it doesn't change their size.
What would you expect to happen to those sections below, that they remain where they are? You need to be a bit bolder and try what is suggested and if there are problems, state what they are, your questions are those of someone unwilling to test, so you'll never get anything done.
You do need to run the report before you'll see the results, so in that respect you'll need to connect to the database first, which is always the case with Crystal, you need data to display a report.
-k
- Thread starter
- #13
thank because i'm stupid you mus take a long time to teach me . i'm sorry. at least i can do like yours sai ang success. but my border can not seen . because it in back of the picture. how to make my border seen in front of bac kground
thank alot lbass
thank alot lbass
- Thread starter
- #14
What do you mean by border? A border around a field would appear on top of the picture. If you have added lines (insert->line), then try inserting a text box instead of the lines, using one of the borders of the box to create your line. These new lines should appear on top of the picture.
-LB
-LB
-
1
- #16
bantakiah:
The solutions is within each helper, maybe we can teach you by handling it in little steps (my english is not so great eather, maybe it helps
1) in crystal reports go to the menu insert-->picture and search the picture you want to set for the background
2) after you found the picture click on the [open] button
3) the picture is attached to your mouse-cursor and can so it can be placed anywhere in the report (place it like lbass said in the page header)
4) between the page header and de details or group section there is a line, put the mouse-cursor on this line till it becomes an arrow-up and arrow-down
5) then click it and hold it to be able to grow the header section
So far, so good...this far you already went of course
6) at page header level, click on the left (grey) side with the right mouse button and go in the menu to [format section]
7) in the format section, the last option is indeed [ ] underlay following section
8) mark this [ ] box
Sofar, so good, the picture is in place, and the underlay following section will work
9) selecting the picture and click (right-mouse)
10) select [format graphic]
11) select [border]
12) if you want select for the sides if they need a border or not
If you already went this far and it is not what you were looking for, then it is perhaps better to explain in little steps the problem you are facing..
-D
The solutions is within each helper, maybe we can teach you by handling it in little steps (my english is not so great eather, maybe it helps
1) in crystal reports go to the menu insert-->picture and search the picture you want to set for the background
2) after you found the picture click on the [open] button
3) the picture is attached to your mouse-cursor and can so it can be placed anywhere in the report (place it like lbass said in the page header)
4) between the page header and de details or group section there is a line, put the mouse-cursor on this line till it becomes an arrow-up and arrow-down
5) then click it and hold it to be able to grow the header section
So far, so good...this far you already went of course
6) at page header level, click on the left (grey) side with the right mouse button and go in the menu to [format section]
7) in the format section, the last option is indeed [ ] underlay following section
8) mark this [ ] box
Sofar, so good, the picture is in place, and the underlay following section will work
9) selecting the picture and click (right-mouse)
10) select [format graphic]
11) select [border]
12) if you want select for the sides if they need a border or not
If you already went this far and it is not what you were looking for, then it is perhaps better to explain in little steps the problem you are facing..
-D
- Thread starter
- #17
- Thread starter
- #18
- Status
Similar threads
- Locked
- Question
- Locked
- Question