HOW TO CONFIGURE ELU32 WITH IP PHONE 4225 2

[Alex1978]

HI, I HAVE MD110 BC11 AND I MUST INSERT ELU32 IN LIM1.

WHAT IS THE INSTRUCTION SET COMMANDS TO CONFIGURE THE BOARD ELU32 WITH IP PHONE 4225?

I HAVE WITH WINFIOL6.0 SEND THIS COMMAND:

CNHUI:BPOS=1-1-50;
IPBOI:BPOS=1-1-50,IP=10.10.24.1,MASK=255,255,255,0
THEN I HAVE RESTART THE BOARD
RFBOI:BPOS=1-1-50;
BLDBE:BPOS=1-1-50,ALLFM=YES;
RESTART SUCCESFULLY.
WITH COMMAND SYEDP:BPOS=1-1-50 THERE IS NOT DIR NUMBER ASSIGNED.

HOW CAN I ASSIGNED THAT NUMBER TO THE 16 IP ADDRESS OF THE ELU32 BOARD?

THERE ARE MANY OTHERS COMMAND TO SEND TO ELU32 BOARD FOR INITIALIZATION IP PHONE 4225 ERICSSON?

MANY THANKS TO EVERYBODY.

 

[Isinor]

Hi,

Initiate some generic extensions...
GESPI:CSP=0,TRAF=xxx,SERV=xxx,CDIV=xxx,ROC=xxx,NPRES=xxx;
GEDIIIR=1234,LIM=1,CSP=1;

Initiate some IP Extensions...
IPEXIIR=1234,PASSW=9999;

Regards
Isinor

 

[lalrl]

But better is to use DBC4425...

 

[whosrdaddy]

remember that there is no "physical" link between the ELU32 and the IP phone. They are both just network devices. you can register up to 48 phones onto one ELU32 with the limitation that you only have 8 simultaneous gateway calls...

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Alex1978]

First, thank to everybody.
I have a DBC4425 sorry...

I have esecuted your information, but I have more difficulty!

I must only try and repair the ELU32 and DBC4425.
Then I need of a simply connection for the phone, and install the board...

1) Is possible to connect with an ethernet cable the DBC4425 to the port of ELU32, simulating an simply rete?

2) After yours command , how I can assign a number to the phone IP ADDRESS?

THIS IS MY SITUATION:

<IPBOI:BPOS=2-1-50,IP=192.168.102.53,MASK=255.255.255.0;
EXECUTED

<GESPI:CSP=2,TRAF=0103071514,SERV=205071010130,CDIV=00013210,ROC=000001,NPRES=001;
EXECUTED

<GEDIIIR=35100,LIM=2,CSP=2;
EXECUTED

<IPEXIIR=35100,PASSW="9999";
EXECUTED

<SYEDP:BPOS=2-1-50;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
002-1-50-00 114 IPL
002-1-50-01 114 IPL
002-1-50-02 114 IPL
002-1-50-03 114 IPL
002-1-50-04 114 IPL
002-1-50-05 114 IPL
002-1-50-06 114 IPL
002-1-50-07 114 IPL
002-1-50-08 114 IPL
002-1-50-09 114 IPL
002-1-50-10 114 IPL
002-1-50-11 114 IPL
002-1-50-12 114 IPL
002-1-50-13 114 IPL
002-1-50-14 114 IPL
002-1-50-15 114 IPL
END
<IPEXPIR=35100;
IP EXTENSION DATA
DIR IP ADDRESS RAS PORT CS PORT PASSWORD
35100 NOT REGISTERED - - 9999

END

<GEDIPIR=35100;
DIRECTORY NUMBER PROFILE
DIR LIM CSP CUST LANG
35100 2 2 - F


<GEDIP:LIC=ALL;
WAIT
WAIT
NOT ACCEPTED

LICENSE(S) NOT INITIATED

I'm very confuse on this argoments...!! thanks a lot

 

[whosrdaddy]

think the other way around:

you can't give the IP address of the phone in the MD110, you must set the address (=GK address) of the ELU32 in the phone's network settings.

the SYEDP command will not help here because resources are virutal, not physical. use IPEXP and IPERP to retrieve information about logged-on phones...

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Isinor]

Hi,

1) Is possible to connect with an ethernet cable the DBC4425 to the port of ELU32, simulating an simply rete?

You should connect the ELU32 to a switch or hub, then put the phone in to the same hub or switch.

2) After yours command, how I can assign a number to the phone IP ADDRESS?

Set the IP address on phone.
Settings... Network menu...
To change settings press 'C * 5' for 4 seconds
Set the Gatekeeper to the ELU32 IP address
Set the Phone to DHCP or put an IP address value manually.
If using a PASSW ensure password is set to YES.

Then log on with the extension number... 35100 and the password 9999





Regards
Isinor

 

[rinop]

If you set manually an IP static,
you can set the phone in the browswer.
insert number IP in the bar of the addresses .
The password of default of the telephone it is “Welcome” while the password admin of default via web it is “ERICSSON” .

 

[whosrdaddy]

admin password is not ERICSSON but Ericsson (mind the casing)

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Alex1978]

Thanks a lot to everybody...
Monday I try every your information!!

But now, weekend of relax !

 

[Alex1978]

YES...VICTORY!

Thanks a lot to everybody, I've programmed my board ELU32 and DBC4425.

I've not installed all the properties, but FUNCTION...this is the most important!

THANKS......!

Alex...