Zeenatullah
Programmer
As i am new to meridain Cs1k so can anyone tell me about how to check system health and version of system though complete codes and cammands
Zeenat Ullah Apollo guy
Zeenat Ullah Apollo guy
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
how to check the system health and software version of CS1K
- Thread starter Zeenatullah
- Start date
- Status
You may want to find a book and do a little reading before jumping right in. Here is a good resource for you to familiarize yourself
- Thread starter
- #3
Zeenatullah
Programmer
Sir, not much New little bit familiar with Meridian I am reading PBXBOOK for a month but please can you describe in commands
Zeenat Ullah Apollo guy
Zeenat Ullah Apollo guy
- Thread starter
- #5
Zeenatullah
Programmer
as it is right to configure the analog phone
LD 10
REQ NEW,CHG
TYPE 500
TN 9 11
CUST 0
DN 2326
REQ END
Zeenat Ullah Apollo guy
LD 10
REQ NEW,CHG
TYPE 500
TN 9 11
CUST 0
DN 2326
REQ END
Zeenat Ullah Apollo guy
LD 137 STAT ELNK - Shows you the status of the Ethernet connection
LD 137 STAT - Shows you the status of the system drives and does a simple validation of the keycode to see if it is corrupted
LD 48 STAT ELAN - Shows you the status of any AML links present
LD 48 STAT MSDL - Shows the status of configured MSDL cards
LD 48 STAT TMDI - Shows the status of configured TMDI cards
LD 2 TTAD - Shows the present system date and time
LD 60 STAT - Shows the status of programmed circuit loops and channels
LD 96 STAT DCH - Shows the status of programmed circuit D channels
LD 22 PRT AHST (or PHST) - prints the history file (AHST=All History in the buffer, PHST=History since last printed)
There's more but these are the ones our first level support folks know and perform daily.
LD 137 STAT - Shows you the status of the system drives and does a simple validation of the keycode to see if it is corrupted
LD 48 STAT ELAN - Shows you the status of any AML links present
LD 48 STAT MSDL - Shows the status of configured MSDL cards
LD 48 STAT TMDI - Shows the status of configured TMDI cards
LD 2 TTAD - Shows the present system date and time
LD 60 STAT - Shows the status of programmed circuit loops and channels
LD 96 STAT DCH - Shows the status of programmed circuit D channels
LD 22 PRT AHST (or PHST) - prints the history file (AHST=All History in the buffer, PHST=History since last printed)
There's more but these are the ones our first level support folks know and perform daily.
Couple more you can add to Wanebo's list
LD 135
STAT CPU - check the state of the CPU(s) and in HA that they are redundant (health 14 is good)
STAT HEALTH - make sure the total health on both CPUs matches
STAT IPL - Check status of links to MGC's
LD 117
STAT SS - Status of your sig servers (see registered set counts and VTRK status)
STAT IPMG - Shows you the registration time of your gateways (can highlight issues if you have a gateway restarting etc.)
LD 135
STAT CPU - check the state of the CPU(s) and in HA that they are redundant (health 14 is good)
STAT HEALTH - make sure the total health on both CPUs matches
STAT IPL - Check status of links to MGC's
LD 117
STAT SS - Status of your sig servers (see registered set counts and VTRK status)
STAT IPMG - Shows you the registration time of your gateways (can highlight issues if you have a gateway restarting etc.)
- Status
Similar threads
- Locked
- Question
- Locked
- Question