Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

How do I setup Mobile Extensions on Nortel CS1k 5.5

Status
Not open for further replies.

TJaramillo

Technical User
Mar 21, 2008
18
US
I have the licenses, i just cant find documentation on how to setup a TN.

Please help.

Thanks.
 
Are you refering to MOBEX TN's?.

I did a script in Procomm to install them as shown below. It should work, although I think one of my colleagues had to make a small change to a CLS entry.

; New Mobex extn provision.was 24th April 2009

; NOTE!
; This program will ONLY work with a Windows version of PROCOMM PLUS!.
; This Procomm Script file is for you to configure a "NEW MOBEX digital extension
; The " ; " denotes that the data on this program script is ignored when the
; file is run.
; The script will also record for you a LOG file such as "pw01.cap" etc.
; The program will use LD 11 for all the changes & LD 81 to print out the TN's.
; Follow the instructions by Ticking the box's on the screen & locating your source file.
; You might need to change the "Transmit Pacing" depending on the software version!
; A higher number is needed to slow the program down for the older processors.
; Make sure that you enter the file name & click on "ACCEPT" to run in your entries.

; Make sure that you enter the Login Name (or Account name for V04.5x onwards!)&
; the Password & click on the "ACCEPT" button to run in your speed call entries.
; If your system does not use any Login name, then just enter any name or c/r in the box.
; You don't need to be LOGGED into the Meridian, before you run the script!.
; The program will still run on older software versions that don't use Named Login. It's
; best if log in first before the program is started. Just enter any name as mentioned above
; & wait 30 seconds before it will commence the input procedure.

; The data that needs to be used should be entered via Microsofts Excel application, using the columns
; as shown in the example. Once you have entered in the required settings, remove the header
; (1st line of data & save the SOURCE file which should be in a *.CSV Format!

; An example of the source file as viewed in text, is shown below.

;TYPE, TN, DES ,CUST,UXTY,UXID,TGAR,NCOS,CLS ,KEY 0,KEY 1,KEY 16,KEY 23,

;UEXT,065 0 00 00,MOBX,0,MOBX,111,0,0,LNA,SCR 65000,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 01,TLSV,0,TLSV,X,0,0, ,SCR 65001,HOT P 5 55000,,,
;UEXT,065 0 00 02,MOBX,0,MOBX,112,0,0, ,SCR 65002,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 03,TLSV,0,TLSV, ,0,0, ,SCR 65003,HOT P 5 55001,,,
;UEXT,065 0 00 04,MOBX,0,MOBX,113,0,0, ,SCR 65004,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 05,TLSV,0,TLSV, ,0,0, ,SCR 65005,HOT P 5 55002,,,
;UEXT,065 0 00 06,MOBX,0,MOBX,114,0,0, ,SCR 65006,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 07,TLSV,0,TLSV, ,0,0, ,SCR 65007,HOT P 5 55003,,,
;UEXT,065 0 00 08,MOBX,0,MOBX,115,0,0, ,SCR 65008,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 09,TLSV,0,TLSV, ,0,0, ,SCR 65009,HOT P 5 55004,,,
;UEXT,065 0 00 10,MOBX,0,MOBX,116,0,0, ,SCR 65010,HOT P 16 8998207825833898,,,
;UEXT,065 0 00 11,TLSV,0,TLSV, ,0,0, ,SCR 65011,HOT P 5 55005,,,

#include "vkeys.inc" ; You must have this file "vkeys.inc"
; located within the "Aspect" folder!
STRING F_Time
string s_opdata[13]

proc main
integer i_evt
integer i_rg2_chc = 3
integer i_rg5_chc = 6
integer i_tmp
integer i_ch
integer i_fch_tx_val
integer i_tx_val
integer i_p

long l_tot_no_lin
long l_lin_cnt
long l_prog_bar_op
long l_fi_sz0
long l_cur_fi_sz0

string s_fi_nm
string s_tx_list = "0,5,10,20,30,40,50,80,100,120,200,300,400,500"
string s_tx_item = "100"
string s_dir
string s_pwd
string s_userid
string s_time_start
string s_date_start

string s_progress
string s_prog_bar
string s_sce_lin

string s_fi_ext_item = "*.CSV"
;string s_type_list = "CHG,NEW,OUT"
;string s_type_item = "CHG"
string s_list_customer = "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87"
string s_customer_item = "0"
string s_list_dcno = "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88"
string s_dcno_item = "1"

dialogbox 0 13 17 476 332 11 "Nortel Procomm script file to enter a new UEXT MOBEX port in LD 11. V01.1 24th April 2009"
groupbox 1 10 7 130 51 ""
radiogroup 2 i_rg2_chc
radiobutton 3 19 16 42 11 "NEW"
; radiobutton 4 19 36 42 11 "CHG"
endgroup
radiogroup 5 i_rg5_chc
radiobutton 6 87 16 50 11 "Digital"
; radiobutton 7 87 36 42 11 "IDC"
endgroup
;combobox 10 102 67 32 252 DROPDOWNLIST s_list_customer s_customer_item
; text 16 16 69 86 11 "Customer No Use up to 87" left
; combobox 9 102 88 32 238 DROPDOWNLIST s_list_dcno s_dcno_item
; text 8 17 90 84 9 "DCNO No Use up to 88" left
dirlistbox 12 55 176 85 94 "*.csv" SINGLE s_fi_nm 21 SORT
editbox 23 386 37 73 11 s_userid 11
editbox 13 386 53 74 11 s_pwd 16 MASKED
editbox 37 417 106 38 11 s_date_start 8
editbox 38 417 147 38 11 s_time_start 8
combobox 24 423 168 30 170 DROPDOWNLIST s_tx_list s_tx_item
dirpath 21 9 164 134 11 s_dir
pushbutton 14 16 118 40 13 "Accept"
pushbutton 15 90 118 40 13 "Cancel"
text 29 169 124 294 11 "If you want the program to Time start, then enter the time in 24Hr format in the box below" center
text 47 217 55 166 11 "Switch Password is Case Sensitive for V4.5 onwards" left
text 25 175 170 246 11 "Select the systems Transmit Pacing. User a higher number on older software!." left
text 22 190 38 190 11 "Name or User ID. (No Name = any character key pressed!)" left
text 34 167 147 248 11 "Pressing the (Space Bar) = Auto Start, or enter the start Time = e.g. 16:20:00 " left
text 35 167 211 290 26 " Please remember to check your capture file settings under the following headings's (Options, Data Options, Setup Files, Capture File Options, Control Options) to UNCHECK the box marked (Query for file name when capture is started)!. " left
text 33 168 240 288 16 " Click (OK) & (OK) again before starting this script program. This will make the script capture the information if the delayed Date / Time start function is used!. " left
text 36 169 82 294 11 "If you want the program to Date start, then enter the Date as e.g. 23/12/05 in the box below" center
text 31 169 106 248 11 "Pressing the (Space Bar) = Auto Start, or enter the required Date for it to run" left
text 39 419 138 34 9 "Hr:Mn:Sc" center
text 40 418 96 34 9 "Dy/Mh/Yr" center
text 32 178 19 282 11 "Enter the systems Login Name and Password in the box's below to run the script file" center
groupbox 41 9 56 130 52 ""
groupbox 49 165 3 302 68 ""
groupbox 50 164 71 304 91 ""
groupbox 51 1 155 146 120 ""
groupbox 52 1 2 146 150 ""
text 53 6 220 36 11 "Source file" left
text 43 6 230 36 11 "location" center
text 42 6 240 36 11 "= *.csv" center

text 54 154 264 320 11 "Columns that will need configuring!" center
text 64 153 276 314 11 "TYPE,TN,DES,CUST,UXTY,UXID,TGAR,NCOS,CLS,KEY 0,KEY 1,KEY 16,KEY 23," center
text 45 153 292 320 11 "Example below = data used!" center
text 48 153 306 318 11 "UEXT,065 0 00 00,MOBX,0,MOBX,111,0,0,LNA CFHA,SCR 65000,HOT P 16 8998207825833898,,," center

; text 44 6 275 136 11 "TGAR,NCOS,CLS,KEY 0,KEY 1,KEY 16,KEY 23," center
; text 60 6 305 136 11 "111,0,0,LNA CFHA,SCR 65000," center
; text 65 6 315 136 11 "HOT P 16 8998207825833898," center
groupbox 46 164 157 304 30 ""
text 55 168 193 290 16 " If you are planning to use the delayed start time / date function, then follow the instruction listed below " left
groupbox 56 164 183 304 78 ""
groupbox 63 10 107 128 34 ""
; text 61 13 115 122 11 "Note!. Check Digit length BLOCK first!" center
; text 62 14 125 122 11 "Type = CPND (MXLN and DFLN = 27)" center
enddialog

while 1
dlgevent 0 i_evt
switch i_evt
case 0
if i_rg2_chc == 3
if nullstr s_date_start
disable dlgctrl 0 14
elseif nullstr s_time_start
disable dlgctrl 0 14
elseif nullstr s_userid
disable dlgctrl 0 14
elseif nullstr s_pwd
disable dlgctrl 0 14
elseif nullstr s_fi_nm
disable dlgctrl 0 14
else
enable dlgctrl 0 14
endif
endif
if i_rg2_chc == 4
if nullstr s_date_start
disable dlgctrl 0 14
elseif nullstr s_time_start
disable dlgctrl 0 14
elseif nullstr s_userid
disable dlgctrl 0 14
elseif nullstr s_pwd
disable dlgctrl 0 14
elseif nullstr s_fi_nm
disable dlgctrl 0 14
else
enable dlgctrl 0 14
endif
endif
endcase
case 5
if i_rg5_chc == 7
enable dlgctrl 0 8
enable dlgctrl 0 16
endif
if i_rg5_chc == 6
disable dlgctrl 0 8
disable dlgctrl 0 16
endif
endcase

case 13
strlen s_pwd i_tmp
if i_tmp < 4
usermsg "Password `"%s`"`n`nThis must be between 4-16 characters in length & it is case sEnsTivE on V04.50 onwards!" s_pwd
sendvkey MAKE_KV(KV_SHIFT,VK_TAB)
endif
endcase
case 14
exitwhile
endcase
case 15
exitwhile
endcase
case 23
strlen s_userid i_tmp
if i_tmp < 1
usermsg "Name or UserID `"%s`"`n`nName can be up to 11 Characters. Otherwise enter a dummy name or press the Space Bar to accept the entry" s_userid
sendvkey MAKE_KV(KV_SHIFT,VK_TAB)
endif
endcase
case 28
exitwhile
endcase
case 29
exitwhile
endcase
case 30
dlgupdate 0 24
endcase
case 37
strlen s_date_start i_tmp
if i_tmp < 1
usermsg "Start Date `"%s`"`n`nmust be 6 Numbers in length and with a (/) in between every 2 digits. or you can just press the Space Bar to leave the box blank to Auto Start the Listing program" s_date_start
sendvkey MAKE_KV(KV_SHIFT,VK_TAB)
endif
endcase
case 38
strlen s_time_start i_tmp
if i_tmp < 1
usermsg "Start Time `"%s`"`n`nmust be 6 Numbers in length and with a :)) in between every 2 digits. or you can just press the Space Bar to leave the box blank to Auto Start the Listing program" s_time_start
sendvkey MAKE_KV(KV_SHIFT,VK_TAB)
endif
endcase
endswitch
endwhile

dlgdestroy 0 cancel

if i_evt != 14
exit
endif

if not fopen 0 s_fi_nm read
errormsg "Couldn't open file `"%s`"." s_fi_nm
else
cnt_no_fi_lines(i_ch,&l_tot_no_lin,&l_fi_sz0)

STATMSG "Waiting for the Digital set auto start date/time program to run. Make sure that auto capture is set correctly!"

fetch txpace i_fch_tx_val
atoi s_tx_item i_tx_val
strcat s_tx_item " ms"
set txpace i_tx_val

datetimestart(s_time_start,s_date_start)
logi(s_userid)
login(s_pwd)

STATMSG "The Digital set auto start date/time program has now started!"

ld_ovl_11(i_rg2_chc)

dialogbox 1 192 146 400 91 14 "New Digital sets Progress Status Bar"
text 1 6 8 218 11 s_progress left
editbox 2 14 22 198 11 s_prog_bar
text 3 14 38 380 11 s_fi_nm left
text 4 14 80 58 11 "Transmit Pace ==" left
text 6 14 60 380 11 s_sce_lin left
text 5 76 80 34 11 s_tx_item left
enddialog

l_prog_bar_op = l_fi_sz0/40

while not feof 0
fgetc 0 i_ch
if not feof 0
ftell 0 l_cur_fi_sz0
if l_cur_fi_sz0 % l_prog_bar_op == 0
strcat s_prog_bar "#"
dlgupdate 1 2
endif
if i_ch == '`r'
loopwhile
endif
if i_ch == '`n'
l_lin_cnt++
strputc s_sce_lin i_p 0
if not nullstr s_sce_lin

get_opdata(s_sce_lin)

strfmt s_progress "Line %ld of %ld" l_lin_cnt l_tot_no_lin
dlgupdate 1 1
dlgupdate 1 6
s_sce_lin = ""
i_p = 0

send_opdata()

loopwhile
endif
endif
strputc s_sce_lin i_p i_ch
i_p++
endif
endwhile


; ex_ovl_11(s_customer_item)
ex_ovl_11()

logo ()
set txpace i_fch_tx_val
fclose 0

endif

dlgdestroy 1 cancel

endproc

proc get_opdata ;#####

param string s_sce_lin

strtok s_opdata[0] s_sce_lin "," ;TYPE
strtok s_opdata[1] s_sce_lin "," ;TN
strtok s_opdata[2] s_sce_lin "," ;DES
strtok s_opdata[3] s_sce_lin "," ;Customer Number
strtok s_opdata[4] s_sce_lin "," ;UXTY
strtok s_opdata[5] s_sce_lin "," ;UXID
strtok s_opdata[6] s_sce_lin "," ;TGAR
strtok s_opdata[7] s_sce_lin "," ;NCOS
strtok s_opdata[8] s_sce_lin "," ;CLS
strtok s_opdata[9] s_sce_lin "," ;KEY 0
strtok s_opdata[10] s_sce_lin "," ;KEY 1
strtok s_opdata[11] s_sce_lin "," ;KEY 16 MWK
strtok s_opdata[12] s_sce_lin "," ;KEY 23 SSU / SCC etc

; strtok s_opdata[11] s_sce_lin "," ;SCPW
; strtok s_opdata[12] s_sce_lin "," ;CLS
; strtok s_opdata[13] s_sce_lin "," ;HUNT
; strtok s_opdata[14] s_sce_lin "," ;AST
; strtok s_opdata[15] s_sce_lin "," ;IAPG
; strtok s_opdata[16] s_sce_lin "," ;KEY 0
; strtok s_opdata[17] s_sce_lin "," ;KEY 1
; strtok s_opdata[18] s_sce_lin "," ;KEY 16
; strtok s_opdata[19] s_sce_lin "," ;KEY 23
; strtok s_opdata[20] s_sce_lin "," ;

endproc

proc send_opdata ;##### Sequence of changes and data input

; waitfor "TYPE"
txdc (s_opdata[0])
waitfor "TN "
txdc (s_opdata[1])
waitfor "DES "
txdc (s_opdata[2])
waitfor "CUST "
txdc (s_opdata[3])
waitfor "UXTY "
txdc (s_opdata[4])
waitfor "UXID "
txdc (s_opdata[5])
; waitfor "FDN "
; txdc (s_opdata[6])
waitfor "TGAR "
txdc (s_opdata[6])
waitfor "NCOS "
txdc (s_opdata[7])
; waitfor "RNPG "
; txdc (s_opdata[9])
; waitfor "SSU "
; txdc (s_opdata[10])
; waitfor "SCPW "
; txdc (s_opdata[11])
waitfor "CLS "
txdc (s_opdata[8])
; waitfor "HUNT "
; txdc (s_opdata[13])
; waitfor "AST "
; txdc (s_opdata[14])
; waitfor "IAPG "
; txdc (s_opdata[15])
waitfor "KEY "
transmit "0 "
txdc (s_opdata[9])
waitfor "KEY "
transmit "1 "
txdc (s_opdata[10])
waitfor "KEY "
transmit "16 "
txdc (s_opdata[11])
waitfor "KEY "
transmit "23 "
txdc (s_opdata[12])

; txdc (s_opdata[20])

waitfor "KEY "
txdc ("")
waitfor "REQ"

; txdc ("NEW")

; else
; endif

endproc

proc cnt_no_fi_lines ;#####

param integer i_ch
param long l_tot_no_lin
param long l_fi_sz0

while not feof 0
fgetc 0 i_ch
if not feof 0
if i_ch == '`n'
l_tot_no_lin++
endif
endif
endwhile

ftell 0 l_fi_sz0
rewind 0

endproc

;proc txdt ;#####

;param string s_txs
;integer i_p = 0
;integer i_ch = -1

; strgetc s_txs i_P i_ch
; i_p++

; while i_ch != 0
; computc i_ch
; strgetc s_txs i_P i_ch
; i_P++
; endwhile

;endproc

proc txdc ;#####

param string s_txs
integer i_p = 0
integer i_ch = -1

strgetc s_txs i_P i_ch
i_p++

while i_ch != 0
computc i_ch
strgetc s_txs i_P i_ch
i_P++
endwhile

computc 13

endproc

proc ld_ovl_11 ;#####

param integer i_rg2_chc

Capture On

; In this area, enter in new prompts that have appeared when running this script using examples
; listed below. Different features & software versions will result in prompts that have not been
; spotted before.

WHEN TARGET 1 "OVL111 " CALL OVL111
WHEN TARGET 2 "OVL013 " CALL OVL013
WHEN TARGET 3 "CTYP " CALL CARR_RETURN
WHEN TARGET 4 "NUID " CALL CARR_RETURN
WHEN TARGET 5 "NHTN " CALL CARR_RETURN
WHEN TARGET 6 "ERL " CALL CARR_RETURN
WHEN TARGET 7 "ECL " CALL CARR_RETURN
WHEN TARGET 8 "FDN " CALL CARR_RETURN
WHEN TARGET 9 "LDN " CALL CARR_RETURN
WHEN TARGET 10 "RNPG " CALL CARR_RETURN
WHEN TARGET 11 "SSU " CALL CARR_RETURN
WHEN TARGET 12 "SCPW " CALL CARR_RETURN
WHEN TARGET 13 "SGRP " CALL CARR_RETURN
WHEN TARGET 14 "SFLT " CALL CARR_RETURN
WHEN TARGET 15 "CAC_MFC " CALL CARR_RETURN

WHEN TARGET 20 "HUNT " CALL CARR_RETURN
WHEN TARGET 21 "LNRS " CALL CARR_RETURN
WHEN TARGET 22 "SCI " CALL CARR_RETURN
WHEN TARGET 23 "PLEV " CALL PLEV_0
WHEN TARGET 24 "DANI " CALL CARR_RETURN
WHEN TARGET 25 "AST " CALL CARR_RETURN
WHEN TARGET 26 "IAPG " CALL CARR_RETURN
WHEN TARGET 27 "MLWU_LANG " CALL CARR_RETURN
WHEN TARGET 28 "MLNG " CALL CARR_RETURN
WHEN TARGET 29 "DNDR " CALL CARR_RETURN
WHEN TARGET 30 " MARP " CALL CARR_RETURN
WHEN TARGET 31 " CPND " CALL CARR_RETURN
WHEN TARGET 32 " VMB " CALL CARR_RETURN

WHEN TARGET 40 "TEN " CALL CARR_RETURN
WHEN TARGET 41 "ECHG " CALL EASY_CHANGE
WHEN TARGET 42 "DATE " CALL CARR_RETURN
WHEN TARGET 43 "PAGE " CALL CARR_RETURN
WHEN TARGET 44 "NACT " CALL CARR_RETURN
WHEN TARGET 45 "ZONE " CALL PLEV_0


txdc ("****")
waitfor ">"

txdc ("LD 11") ; Start of access into LD 11
waitfor "REQ"
if i_rg2_chc == 3
txdc ("NEW")
else
txdc ("CHG")
endif
waitfor "TYPE"

STATMSG " Start of Progress status bar and new extensions to be provided in LD 11"

endproc

proc ex_ovl_11 ;##### Print out the sets in LD 81

;param string s_customer_item

pause 3
txdc ("")
txdc ("****")
waitfor ">"

txdc ("LD 81")
waitfor "REQ "
txdc ("LST")
waitfor "CUST "
txdc ("0")
; waitfor "DATE "
; txdc ("")
; waitfor "PAGE "
; txdc ("")
waitfor "DES "
txdc ("")
waitfor "FEAT "
txdc ("UEXT")
waitfor "FEAT "
txdc ("")
waitfor "REQ "
txdc ("****")
waitfor ">"

Capture off

endproc

PROC DATETIMESTART

param string s_time_start
param string s_date_start
integer i_tmp

strlen s_date_start i_tmp
if i_tmp >5
strlen s_time_start i_tmp
if i_tmp <2
s_time_start = "00:10:00"
endif
endif
strlen s_time_start i_tmp
if i_tmp >5
strlen s_date_start i_tmp
if i_tmp <2
s_date_start = $DATE
endif
endif

Waituntil s_time_start s_date_start
endproc

Proc TTY_LOGIN
pause 3
txdc ("LOGI")
endproc

proc logi ;#####
param string s_userid

WHEN TARGET 0 "OVL014 " CALL OVL014
WHEN TARGET 1 "OVL428 " CALL OVL428
WHEN TARGET 2 "SCH0510 " CALL OVL014
WHEN TARGET 3 "OVL013 " CALL TTY_LOGIN
WHEN TARGET 4 "SCH5289 " CALL SCH5289
WHEN TARGET 5 "SCH5290 " CALL SCH5290
WHEN TARGET 6 "SCH3634 " CALL SCH3634
WHEN TARGET 7 "SCH0494 " CALL SCH0494
WHEN TARGET 9 "OVL111 " CALL OVL111
WHEN TARGET 10 "SCH0510 " CALL SCH0101
WHEN TARGET 11 "SCH101 " CALL SCH0101
WHEN TARGET 12 "SCH1111 " CALL SCH1111
WHEN TARGET 13 "SCH2116 " CALL SCH2116
WHEN TARGET 22 "SCH3634 " CALL SCH3634


transmit "LOGI "
; txdc ("LOGI ")
txdc (s_userid)
waitfor "PASS?"
endproc

proc login ;#####
param string s_pwd
txdc (s_pwd)
waitfor ">"
endproc

proc logo ;#####
txdc ("LOGO") ; Add on this line ";" to allow the program to remain logged in!.
F_Time=$TIME
statmsg "LD 11 New Digital Set script file has now been Completed`n`n at %s" F_TIME

usermsg "LD 11 New Digital Set script file is now Complete`n`n at %s" F_TIME
endproc

PROC PLEV_0
; pause 1
txdc ("0")
ENDPROC

PROC CARR_RETURN
txdc ("")
ENDPROC

PROC EASY_CHANGE
pause 1
txdc ("NO")
ENDPROC

Proc OVL013
txdc ("****")
ENDPROC

PROC SCH2116
txdc ("****")
waitfor ">"
USERMSG "Script failed, due to the Digital set TN already exists!"
exit
ENDPROC

PROC SCH5289

txdc ("****")
waitfor ">"
txdc ("LD 49")
waitfor "REQ "
txdc ("NEW")
waitfor "TYPE "
txdc ("IDC")
USERMSG "Script failed, due to the IDC tree selected is not yet created. Create an IDC tree in LD 49 first!"
EXIT
waitfor "CUST "
; txdc (s_customer_item)
waitfor "DCNO "
; txdc (s_dcno_item)
waitfor "IDGT"
txdc ("")
ENDPROC

PROC SCH5290
txdc ("****")
waitfor ">"
USERMSG "Script failed, due to the wrong DCNO or IDC number being selected on the script file!"
exit
ENDPROC

PROC SCH3634
TRANSMIT "^M~~~~"
ENDPROC

PROC SCH0494
txdc ("****")
waitfor ">"
USERMSG "Script failed, due to a existing IDC Table on the database!"
exit
ENDPROC

PROC SCH1111
txdc ("NO")
PAUSE 1
ENDPROC

PROC OVL014
STATMSG "Please wait 30 seconds as the TTY is already logged in!"
ENDPROC

PROC OVL111
txdc ("****")
waitfor ">"
USERMSG "Script failed, as the TTY user is NOT logged into the system!"
exit
ENDPROC

PROC OVL428
txdc ("****")
USERMSG "Script failed. The Login name & password combination is invalid. Check the password & login name & try again.! On software versions V04.5x onwards, check if the password uses case SeNSiTivItY!"
exit
ENDPROC

PROC SCH0101
pause 2
transmit "****^M"
waitfor ">"
STATMSG "Please wait 30 seconds as the TTY is already logged in!"
ENDPROC


; The information listed below has been taken from the "vkeys.inc" file.
; I have added in one ";" against each line for use with this file!.
; Should your copy of "vkeys.inc" be missing or damaged, then you can copy this
; section listed below with one of the ";" removed for each line!.


;;Definitions of standard virtual key code values
;;**********************************************************************
;;* VKEYS.INC
;;* Copyright (c) 1999 Symantec Corporation
;;*
;;* Definitions of standard virtual key code values. Use these macro
;;* definitions in your ASPECT script files rather than hard-coded
;;* constants to improve maintainability and readability. For more
;;* information, see the keyval and vkey conventions described in the
;;* Windows ASPECT Script Language reference manual.
;;**********************************************************************

;#ifndef _INC_VKEYS ; if file not already included
;#define _INC_VKEYS ; prevent further inclusion

;;**********************************************************************
;;* Macro definitions of standard virtual key code values
;;**********************************************************************

;#define VK_LBUTTON 0x01 ; Left mouse button
;#define VK_RBUTTON 0x02 ; Right mouse button
;#define VK_CANCEL 0x03 ; Ctrl-Break
;#define VK_MBUTTON 0x04 ; Middle mouse button
;; 0x05-0x07 ; Undefined
;#define VK_BACK 0x08 ; Backspace key
;#define VK_TAB 0x09 ; Tab key
;; 0x0A-0x0B ; Undefined
;#define VK_CLEAR 0x0C ; Clear key or Keypad 5 with Num lock off
;#define VK_RETURN 0x0D ; Enter or Return key
;; 0x0E-0x0F ; Undefined
;#define VK_SHIFT 0x10 ; Shift key
;#define VK_CONTROL 0x11 ; Control or Ctrl key
;#define VK_MENU 0x12 ; Menu or Alt key
;#define VK_PAUSE 0x13 ; Pause key
;#define VK_CAPITAL 0x14 ; Capital or Caps Lock key
;; 0x15-0x19 ; Reserved for Kanji Systems
;; 0x1A ; Undefined
;#define VK_ESCAPE 0x1B ; Esc or Escape key
;; 0x1C-0x1F ; Reserved for Kanji Systems
;#define VK_SPACE 0x20 ; Spacebar
;#define VK_PRIOR 0x21 ; Page Up key
;#define VK_NEXT 0x22 ; Page Down key
;#define VK_END 0x23 ; End key
;#define VK_HOME 0x24 ; Home key
;#define VK_LEFT 0x25 ; Left arrow key
;#define VK_UP 0x26 ; Up Arrow key
;#define VK_RIGHT 0x27 ; Right Arrow key
;#define VK_DOWN 0x28 ; Down Arrow key
;#define VK_SELECT 0x29 ; Select key
;#define VK_PRINT 0x2A ; Keyboard (OEM) specific
;#define VK_EXECUTE 0x2B ; Execute key
;#define VK_SNAPSHOT 0x2C ; Print Screen key
;#define VK_INSERT 0x2D ; Insert key
;#define VK_DELETE 0x2E ; Delete key
;#define VK_HELP 0x2F ; Help key
;#define VK_0 0x30 ; 0 key
;#define VK_1 0x31 ; 1 key
;#define VK_2 0x32 ; 2 key
;#define VK_3 0x33 ; 3 key
;#define VK_4 0x34 ; 4 key
;#define VK_5 0x35 ; 5 key
;#define VK_6 0x36 ; 6 key
;#define VK_7 0x37 ; 7 key
;#define VK_8 0x38 ; 8 key
;#define VK_9 0x39 ; 9 key
;; 0x3A-0x40 ; Undefined
;#define VK_A 0x41 ; A key
;#define VK_B 0x42 ; B key
;#define VK_C 0x43 ; C key
;#define VK_D 0x44 ; D key
;#define VK_E 0x45 ; E key
;#define VK_F 0x46 ; F key
;#define VK_G 0x47 ; G key
;#define VK_H 0x48 ; H key
;#define VK_I 0x49 ; I key
;#define VK_J 0x4A ; J key
;#define VK_K 0x4B ; K key
;#define VK_L 0x4C ; L key
;#define VK_M 0x4D ; M key
;#define VK_N 0x4E ; N key
;#define VK_O 0x4F ; O key
;#define VK_P 0x50 ; P key
;#define VK_Q 0x51 ; Q key
;#define VK_R 0x52 ; R key
;#define VK_S 0x53 ; S key
;#define VK_T 0x54 ; T key
;#define VK_U 0x55 ; U key
;#define VK_V 0x56 ; V key
;#define VK_W 0x57 ; W key
;#define VK_X 0x58 ; X key
;#define VK_Y 0x59 ; Y key
;#define VK_Z 0x5A ; Z key
;#define VK_WINDOWSL 0x5B ; Windows key (left)
;#define VK_WINDOWSR 0x5C ; Windows key (right)
;#define VK_APPLICATION 0x5D ; Application key
;; 0x5E-0x5F ; Undefined
;#define VK_NUMPAD0 0x60 ; Numeric Keypad 0
;#define VK_NUMPAD1 0x61 ; Numeric Keypad 1
;#define VK_NUMPAD2 0x62 ; Numeric Keypad 2
;#define VK_NUMPAD3 0x63 ; Numeric Keypad 3
;#define VK_NUMPAD4 0x64 ; Numeric Keypad 4
;#define VK_NUMPAD5 0x65 ; Numeric Keypad 5
;#define VK_NUMPAD6 0x66 ; Numeric Keypad 6
;#define VK_NUMPAD7 0x67 ; Numeric Keypad 7
;#define VK_NUMPAD8 0x68 ; Numeric Keypad 8
;#define VK_NUMPAD9 0x69 ; Numeric Keypad 9
;#define VK_MULTIPLY 0x6A ; Multiply key
;#define VK_ADD 0x6B ; Add key
;#define VK_SEPARATOR 0x6C ; Separator key
;#define VK_SUBTRACT 0x6D ; Subtract key
;#define VK_DECIMAL 0x6E ; Decimal key
;#define VK_DIVIDE 0x6F ; Divide key
;#define VK_F1 0x70 ; Function key F1
;#define VK_F2 0x71 ; Function key F2
;#define VK_F3 0x72 ; Function key F3
;#define VK_F4 0x73 ; Function key F4
;#define VK_F5 0x74 ; Function key F5
;#define VK_F6 0x75 ; Function key F6
;#define VK_F7 0x76 ; Function key F7
;#define VK_F8 0x77 ; Function key F8
;#define VK_F9 0x78 ; Function key F9
;#define VK_F10 0x79 ; Function key F10
;#define VK_F11 0x7A ; Function key F11
;#define VK_F12 0x7B ; Function key F12
;#define VK_F13 0x7C ; Function key F13
;#define VK_F14 0x7D ; Function key F14
;#define VK_F15 0x7E ; Function key F15
;#define VK_F16 0x7F ; Function key F16
;#define VK_F17 0x80 ; Function key F17
;#define VK_F18 0x81 ; Function key F18
;#define VK_F19 0x82 ; Function key F19
;#define VK_F20 0x83 ; Function key F20
;#define VK_F21 0x84 ; Function key F21
;#define VK_F22 0x85 ; Function key F22
;#define VK_F23 0x86 ; Function key F23
;#define VK_F24 0x87 ; Function key F24
;; 0x88-0x8F ; Unassigned
;#define VK_NUMLOCK 0x90 ; Num Lock key
;#define VK_OEM_SCROLL 0x91 ; Scroll Lock key
;; 0x92-0xB9 ; Unassigned
;; 0xBA-0xC0 ; Keyboard (OEM) specific
;; 0xC1-0xDA ; Unassigned
;; 0xDB-0xE4 ; Keyboard (OEM) specific
;; 0xE5 ; Unassigned
;; 0xE6 ; Keyboard (OEM) specific
;; 0xE7-0xE8 ; Unassigned
;; 0xE9-0xF5 ; Keyboard (OEM) specific
;; 0xF6-0xFE ; Unassigned

;;**********************************************************************
;;* Useful macros for testing and forming key values from keyboard
;;* shift states and virtual key code values.
;;**********************************************************************

;#define KV_SHIFT 0x01 ; Shift key pressed
;#define KV_CTRL 0x02 ; Ctrl key pressed
;#define KV_ALT 0x04 ; Alt key pressed
;#define KV_EXT 0x08 ; Extended key flag
;#define KV_CAPSLOCK 0x10 ; Caps Lock key toggled on

;#define MAKE_KV(skeys,vkey) (((skeys) << 8) | (vkey))

;#define KV_VKEY(keyval) ((keyval) & 0xFF)
;#define KV_SKEYS(keyval) ((keyval) >> 8)

;#define KV_SHIFTKEY(keyval) (KV_SKEYS(keyval) & KV_SHIFT)
;#define KV_CTRLKEY(keyval) (KV_SKEYS(keyval) & KV_CTRL)
;#define KV_ALTKEY(keyval) (KV_SKEYS(keyval) & KV_ALT)
;#define KV_EXTKEY(keyval) (KV_SKEYS(keyval) & KV_EXT)

;#endif ; _INC_VKEYS


All the best

Firebird Scrambler
Meridian Programmer in the UK

If it's working, then leave it alone!.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top