Hipath4000 V5 Reinstallation

[Hamid2018]

thread965-1744332
& thread965-1775410
HiPath 4000 V5 System Components - Software - Installation & Configuration.pdf
Dears
Hi,
I am trying to re-install Operating system of a Hipath4000 V5 (with HDCF Card and original hard disk MHW2060AT) Duplex and I have red the attached PDF from Siemens and also I have red mentaioned threads but after doing the steps like this:
1- connect hard disk to computer directly (via USB IDE Adaptor)

​

---- OK
2- initialize disk

​

---- OK
3- format disk as FAT32

​

---- OK
4- copying "V2.0_HDCF_Boot_Image" to disk using hdclone tool

​

---- OK
5- doing step 1 to 4 on CF card

​

---- OK
6- connect hard disk and CF card to HDCF card and insert to Hipath4000 CPCI and power on

at this step if I ping 192.0.2.3 there is no answer from hipath and when I connect to ADP via Serial cable comport4 speed 38400 the out put is like this and scrolling and cannot start system with error 8864 and fault on PDS:

ERROR 8864

START BOOT VERSION H062-N-068 (FLASH 2 LOADED) CARD TYPE: DSCXL-X300
01 0020100B LAN 0290 MAC: ** ** ** ** **
04 015213A8 V.24 0080
06 12098086 LAN-UW7 0290 MAC: ** ** ** ** **
0A 4028110A CGA5L 0480
14 33301344 PCI-PCI 02B0
0E 06801095 IDE 0290
18 33201344 NORTH 02A0
RESTART REASON DETERMINATION
RESTART REASON (RR) SAVED IN BCA:81
RR IN HW PORTS: SUM (FWLP / RRP):2000 (0086 / 2004 )
RESTART REASON : POWERON

RESTART MANAGER DATA:
HD-PDS MO-PDS HD-GLA RESCUE
SCSI ID : 00 05 00 00
AREA SIGN :
AREA NAME : PDS PDS GLA GLA
RELOAD SEQ. : 01 02 03 04
AREA STATUS : FAULT ACTIVE ENABLE DISABLE
AREA CONFIG.: ENABLE ENABLE ENABLE DISABLE
ACTIVE LOAD AREA: MO-PDS
RESTART REASON : POWERON
HARD REST COUNT : 00
RELOAD COUNT : 02
SYSTEM RELOAD : TRUE

CPU-ID : GenuineIntel
*********************************************

PCB-ID : 0B SHELF-ID : 00 SLOT-ID : 01
MEMORY:
LOCAL MEMORY:
CAS : 3
FINE ADJUST : 18
DQS DELAY : 11
SIZE : 1024 MB
BEGIN : 00000000
END : 3FFFFFFF
EXTENDED DDR RAM FOUND
FORMAT MEMORY
00000000 0009FFFF
000C0000 0105FFFF
01070000 0120FFFF
01220000 012C0F1F
012C1F20 012D07FF
012D0D73 012D13FF
012D2000 3FFFFFFF
COPY BOOT TO LM

NMI: NMI-REGISTER (PORT 1680H) : 0000
SETTING TEMPERATURE LIMITS OK
TEMPERATURE:
ACT TEMP CPU: 42
ACT TEMP BOARD: 26
OVER TEMP CPU: 90
OVER TEMP BOARD: 55
OVER TEMP HYSTERESE 0
ACT TEMP STATUS: 80
FAN: 1050 1020 960 990 STATUS: 00

***** MULTI BIT ERROR MONITORING ENABLED *****

Getting MCM Type YES
*** Board = ADP ***
MCM: *** INIT ***
RTC already running
DATE:
CURRENT DATE: 2000 - 1 - 19
CURRENT TIME: 3 : 0 : 2

PMT-INIT
WAITING FOR HD PON-TO-READY

ATTACH LOAD AREA: SCSI ID - 05
AREA-NAME - PDS

VENDOR: ATA HD PRODUCT: STI Flash 8.0.0 REVISION: 01/1
DEVICE TYPE: DIRECT-ACCESS DEVICE
SIZE: 1953 MB ( 31263 * 64KB, 4001761 SECTORS) GRAN: 512 BYTES

AREA FOUND AT :A1H6E: IS CONSISTENT

WRONG APS - PLEASE CHANGE HARDDISK
ERROR 8864

also if I try to install the Operating system as connecting hard disk localy and using PC-HI -> Hicom-HD -> HD-Init SCSI-> 1-HD -> OK -> Layout:h4k-v5-hd/Mediatype: HD -> OK this error comes up in seprate window: "child killed: segmentation violation"

Any Help would be appreciated

Best Regards
Hamid

 

[donb01]

I've never used PC-HI, but from what we went over briefly in class that was supposed to be the tool to use. If there is an option in there to completely reformat and re-partition the drive I would do that, and then load the system image onto the disk.

Have you re-seated the main processor board and the disk controller board? I assume you have, but just in case it never hurts to clean up the connections.



Don Bruechert, Voice Comm Analyst II
CareTech Solutions @ Holy Family Memorial
Manitowoc, WI, USA

 

[Hamid2018]

Dear
donb01 (IS/IT--Management)

Thank You for your answer.
I found the problem one of my colligues downloaded the wrong version of boot Image "V2.0_HDCF_Boot_Image" and placed it in the path of hipath 4K OS installation, by using the right one "V5.0_HDCF_Boot_Image" the installation was successful.
and I have an other question about using PCHI there is an option for installation of SCSI but it doesnt work for version5 what iis it for?

Best Regards.
Hamid

 

[sbcsu]

The SCSI was for the earlier HiCom 300 Systems that uses SCSI Hard Disk Drives only.