hipath 4000V5 sip trunk to CUCM V9.0

[Hamid2018]

thread965-1756203

Dears Hi,
I'm trying to configure a SIP trunk from hipath4K V5 via STMI2 to CUCM V9 by use of attached document but when I dial numbers like 5997 the STMI4 card blinks but no sound transmitted and no call is connected, commands i inserted is as following:
ADD-WABE:5000&&5997,,,STN,N,,,,,,,,;
ADD-WABE:5998,,,TIE,N,,,,,,,,;
ADD-WABE:5999,,,NETRTE,N,,,,,,,,;
ADD-UCSU:LTU,1,9,""Q2266-X "",L80XF,LOCAL,,"",,,,,,,0;
ADD-BFDAT:1,HG3550&SIP&HG3530,BCHL60,;
CHA-BFDAT:CONT,1,HG3550,1,3,;
CHA-BFDAT:CONT,1,SIP,50,,1;
CHA-BFDAT:CONT,1,HG3530,10,,1;
CHA-BFDAT:OK,1,YES;
ADD-BCSU:IPGW,1,9,79,""Q2316-X "",1,0,1,,1,1,30,,,0;
ADD-CGWB:9,79,NORMAL,10.200.0.200,255.255.255.0;
CHANGE-CGWB:CGW,9,79,GLOBIF,,,213,NO,0,10.200.0.1,4060,100MBFD,10,0,0,0,4061,0.0.0.0;
CHANGE-CGWB:CGW,9,79,SERVIF,""TRM"";
CHANGE-CGWB:CGW,9,79,ASC,29100,29219,184,104,YES,YES,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO3,G723,NO,30;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,9,79,ASC,,,,,,,,,PRIO7,G729AB,YES,20;
CHANGE-CGWB:CGW,9,79,DSP,60;
CHANGE-CGWB:CGW,9,79,GKDATA,,1719,""PRIMARYRASMANAGERID"",,,1719,""SECONDARYRASMANAGERID"",,120;
CHANGE-CGWB:CGW,9,79,MGNTDATA,,8000,,443;
CHANGE-CGWB:CGW,9,79,DMCDATA,0;
CHANGE-CGWB:CGW,9,79,WBMDATA,""HP4K-DEVEL"",,ENGR;
CHANGE-CGWB:CGW,9,79,WBMDATA,""HP4K-SU"",,SU;
CHANGE-CGWB:CGW,9,79,WBMDATA,""HP4K-ADMIN"",,ADMIN;
CHANGE-CGWB:CGW,9,79,WBMDATA,""HP4K-READER"",,READONLY;
CHANGE-CGWB:CGW,9,79,GWDATA,""PRIMARYRASMANAGERID"",;
CHANGE-CGWB:CGW,9,79,H235DATA,NO,NO,""siemensGateway2003"",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,9,79,LEGKDATA,44,5999,NO;
CHANGE-CGWB:CGW,9,79,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,9,79,SIPTRSSA,NO,0.0.0.0,5060,5061,120,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,9,79,DLSDATA,,10444,NO;
CHANGE-CGWB:CGW,9,79,JB,40,120,20,4,60,200,2;
ADD-TDCSU:NEW,1-09-079-0,59,59,0,0,1,1,1,""SIP TRUNK IT"",1,PSS1V2,8,,NONE,,,,GDTR,N,TIE,NONE,N,0,,,,,,,31,MANY,1,0,1,1,EMPTY,59,10,N,,,,,,16,8,1,10,1,EC&G711&G729AOPT,,103,DSC,Y,TRADITIO,HG3550IP,1&&30,N,1,10,0,0,0,0,0,Y;
ADD-RICHT:CD,103,5999,,,0,ALL,""SIP TR IT "",,,103,,,,103,,,,,,103,,,203,NEUTRAL,NO,NO,;
ADD-GKREG:44,INTGW&REGGW&HG3550V2&SIP,,,0,0,1,""SIP TR IT"",;
ADD-GKREG:45,EXTGW&HG3550V2&SIP,172.16.13.100,5060,0,0,1,,TRADITIO;

could any one help me?
isn't any need to add any ldpln?

Best Regards
Hamid

 

[sbcsu]

Without looking in to it at great detail - you need to 'send' those numbers down that RICHT

CHA-WABE:5000&&5997,103;

 

[Hamid2018]

yes I did,
I had been entered as following:
CHANGE-WABE:5000&&5499,103,,;
CHANGE-WABE:5500&&5997,103,,;

 

[Hamid2018]

thank you dear SBCSU for your answering.
is there any problem with this part?

CHANGE-CGWB:CGW,9,79,LEGKDATA,44,5999,NO;

 

[Moriendi]

The STMI needs to know the destination IP. It gets the IP from either being passed it via LDAT, or it takes it from a configured profile on the STMI.

Connection to native SIP should use the SIP profile from the STMI GUI. I can't remember if there is a CUCM profile in V5. Maybe. If not, you could try NatTrkEnt profile (something like that, if that's not exactly right).

Using a profile rather than GKREG allows you to take advantage of the extra configuration parameters available for SIP provision, which are accessed via the STMI, but not from the RMX. If you are using GKREG, then SIP profiles are turned off.

If you haven't configured a profile in the STMI, you need to pass the IP address from GKREG into LDAT which sends it to the card. So your LDAT should specify GW 45 as the destination, but you haven't posted your LDAT config.

Taking a wireshark trace will help you determine the problem, ie does 4K send the invite or not. Are both sides tcp/udp or are they different, etc.

 

[adibv]

Durring a dial is there any occupancy on B-channel on 4k-IP Trunk to CUCM 9.1 ?
dis-buend:,b;
dis-sdsu:all, ..... on STMI pen with trunk

On STMI EVTLOG do you have any Error "403 Forbidden" ?

Check on STMI WBM -> Explorers -> Voice gateway -> SIP trunk profile parameter:
SIP protocaol varian for IP netw : SIP-Q or Native SIP
Use profile for trunks via Native SIP : YES

Check on STMI WBM -> Explorers -> Voice gateway -> SIP parameters:

Try also with SIP via UDP : YES

Check on STMI WBM -> Explorers -> Voice gateway -> Codec parameters:
Clear mode(Clear channel data) : OFF

On V5 you have SIP trunk profile for cisco UCM :
STMI WBM -> Explorers -> Voice gateway -> SIP trunk profiles - Cisco UCM