HiPath 4000 V5 ISDN PRI B number sending incomplete

[hipath0514]

I need help on configuration of our new ISDN PRI.

The problem as per our telco provider is I am sending an incomplete call party number.

Lets say I dialled 3002442, they will see in their trace that I am sending all the numbers but not in the block format. Below is the trace from the telco provider.

Called party number
- Length: 2 (02h)
- Type of number: Unknown (0)
- Numbering plan: ISDN/telephony numbering plan (Rec. E.164) (1, 01h)
- Number digits: 3High layer compatibility
- Length: 2 (02h)
- Coding standard: ITU-T standardized coding (0)
- Interpretation: First (primary or only) high layer characteristics identification to be used in
the call (4)
- Presentation method of protocol profile: High layer protocol profile (without specification of
attributes) (1)
- High layer characteristics identification: Telephony (1, 01h)

PCM Conn1 TS:16 Subch:0xFF Type:hdlc Id:172 Time:2012.10.30 14:41:10.404589000
VALID FRAME
INFO
SAPI: 0 (0h) - Call control procedures
C/R: 0 (0h)
TEI: 0 (0h) - Non-automatic TEI assignment user equipment
NS: 012 (0CH)
NR: 007 (07H)
P/F: 0 (0h)
08 02 00 09 7B 70 07 81 30 30 32 34 34 32
INFORMATION
- Protocol discriminator: Rec. Q.931/I.451 User-Network call control messages (8, 08h)
Call reference
- Length: 2 (02h)
- The message is sent to the side that originates the call reference (0)
- value: 9 (0009h)
Called party number
- Length: 7 (07h)
- Type of number: Unknown (0)
- Numbering plan: ISDN/telephony numbering plan (Rec. E.164) (1, 01h)
- Number digits: 002442


My configuration in HiPath 4000 V5 is below...

DID Block is 3045100 to 3045199 with ANI Masking.

DIS-TDCSU:1-1-25-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-01-025-0 TGRP = 23 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 250 COPNO = 250 DPLN = 0 |
| ITR = 0 COS = 250 LCOSV = 1 |
| LCOSD = 1 CCT = ETPI ISDN DESTNO = 14 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = CO |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = Y |
| SUPPRESS = 0 DGTPR = 269 CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = 3045 |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 14 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 250 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = |
| TCCID = SECLEVEL = TRADITIO |
|---------------------------------------------------------------------------|
| BCNEG = Y BCGR = 1 LWPAR = 14 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

DIS-KNDEF:14;
H500: AMO KNDEF STARTED
VIRTUAL NODE TABLE
+-----------+-------+--------------+--------------+-----------+-----+-----+----+
| VIRTUAL | TYPE | ISDN (E.164) | PRIVATE(PNP) | UNKNOWN |POPU-| CAC |DFLT|
| NODE | | CC | L2 | | LA- | PRE-| |
| NUMBER | | AC | L1 | |TION | FIX | |
| | | LC SK | L0 SK | NODECD SK | | | |
| | | UL | UL | VNRGRP | | | |
+===========+=======+==============+==============+===========+=====+=====+====+
| 14 |OWN | | | | 1| | |
| | | | | | | | |
| | | 3045 4 | | | | | |
| | | EXT | EXT | 0 | | | |
+ +=======+==============+==============+===========+=====+=====+====+
| | DPLN | ADPLN | |
+ +=======+==============+==============+===========+=====+=====+====+
+ | | |
+-----------+-------+--------------+--------------+-----------+-----+-----+----+

DIS-KNFOR:14;
H500: AMO KNFOR STARTED
+-----------------------------------------------------------------------------+
| NUMBERING PLAN |
| ISDN |
+------------+----------+----------+----------+-------+-------+------+--------+
| DNNO | TONIN | TONOUT | SCRE | SEND | SEND | OVRD | ERROPT |
| | | | | CALL | CONN | CAT | |
+------------+----------+----------+----------+-------+-------+------+--------+
| 14 | | UNKNOWN | NETWPROV | SEND1 | SEND1 | YES | IGNOR |
+------------+----------+----------+----------+-------+-------+------+--------+


Thank you in advance...

 

[sbcsu]

so they are receiving all the digits but not all at the one time?

you need to setup the LDPLN's to pad out the required digits as follows:

if you need to send 3002442 then your LDPLN should be something like this

ADD-LDPLN:LCRPATT,0,9-W-3-XXXXXX etc.

your corresponding LODR in the LDAT should say
ECHO,3
ECHO,4
END

so anytime a user dials 9 for a line then the digit 3 the system will wait for a further 6 digits before sending them all at once to the provider.

 

[hipath0514]

Hi,

Thanks for your help..


What if my access code is 823-X?

Do i need to change this to 823-W-3-XXXXXX or 823-W-XXXXXX?

The number 3002442 is the one that I dialled.

Thanks again

 

[sbcsu]

hi
well it depends on what your end users want
the 'W' is wait for dummy dial tone and is counted as a field when you are setting up the LODR
the main part is that you determine how many digits are the correct amount to send to line and pad them out with x's