Hi,
Call flow:
PSTN > PRI > Hipath > BRI > Cisco router (CallManager Express) > BRI > Hipath > local phone
Siemens is rejecting the incoming call with Cause i = 0x859C - Invalid number format (incomplete number).
Below you can see the ISDN messages log from Cisco:
363865: Aug 7 15:50:52.279: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x0204
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9FAA068001008201008B0100A10B02028C2E02012903020780
Facility i = 0x9FAA068001008201008B0102A11402028C2F02013B300B30090A01050A01040A0103
Progress Ind i = 0x8483 - Origination address is non-ISDN
Progress Ind i = 0xA190 - Reserved value
Calling Party Number i = 0x0083, '488111222333'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '806'
Plan:Unknown, Type:Unknown
Sending Complete
Locking Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x80
363866: Aug 7 15:50:52.487: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8204
Channel ID i = 0xA98381
Exclusive, Channel 1
363867: Aug 7 15:50:52.487: //36803/96C55367827F/CCAPI/cc_api_call_proceeding:
Interface=0x15E3F404, Progress Indication=NULL(0)
363868: Aug 7 15:50:52.579: ISDN BR0/0/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x8204
Cause i = 0x859C - Invalid number format (incomplete number)
363869: Aug 7 15:50:52.579: ISDN BR0/0/0 Q931: TX -> RELEASE pd = 8 callref = 0x0204
Cause i = 0x809C - Invalid number format (incomplete number)
The direct connections from Cisco to Siemens are OK:
Local phone > Cisco (CallManager Express) > BRI > Hipath > Local phone
Working log:
363587: Aug 7 15:41:45.075: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x0203
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9FAA068001018201018B0100A11B020202E502010080124B617A6D696572637A616B2C204D6172656B
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '48111222333'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '806'
Plan:Unknown, Type:Unknown
363588: Aug 7 15:41:45.247: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8203
Channel ID i = 0xA98381
Exclusive, Channel 1
363589: Aug 7 15:41:45.247: //36744/54C358E69A16/CCAPI/cc_api_call_proceeding:
Interface=0x15E3F404, Progress Indication=NULL(0)
I can see that the only difference in the SETUP message between working and not working scenarios is Progress Ind i = 0xA190 - Reserved value in the not working one.
Do you know which Hipath setting is responsible for rejecting this call?
Call flow:
PSTN > PRI > Hipath > BRI > Cisco router (CallManager Express) > BRI > Hipath > local phone
Siemens is rejecting the incoming call with Cause i = 0x859C - Invalid number format (incomplete number).
Below you can see the ISDN messages log from Cisco:
363865: Aug 7 15:50:52.279: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x0204
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9FAA068001008201008B0100A10B02028C2E02012903020780
Facility i = 0x9FAA068001008201008B0102A11402028C2F02013B300B30090A01050A01040A0103
Progress Ind i = 0x8483 - Origination address is non-ISDN
Progress Ind i = 0xA190 - Reserved value
Calling Party Number i = 0x0083, '488111222333'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '806'
Plan:Unknown, Type:Unknown
Sending Complete
Locking Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x80
363866: Aug 7 15:50:52.487: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8204
Channel ID i = 0xA98381
Exclusive, Channel 1
363867: Aug 7 15:50:52.487: //36803/96C55367827F/CCAPI/cc_api_call_proceeding:
Interface=0x15E3F404, Progress Indication=NULL(0)
363868: Aug 7 15:50:52.579: ISDN BR0/0/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x8204
Cause i = 0x859C - Invalid number format (incomplete number)
363869: Aug 7 15:50:52.579: ISDN BR0/0/0 Q931: TX -> RELEASE pd = 8 callref = 0x0204
Cause i = 0x809C - Invalid number format (incomplete number)
The direct connections from Cisco to Siemens are OK:
Local phone > Cisco (CallManager Express) > BRI > Hipath > Local phone
Working log:
363587: Aug 7 15:41:45.075: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x0203
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9FAA068001018201018B0100A11B020202E502010080124B617A6D696572637A616B2C204D6172656B
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '48111222333'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '806'
Plan:Unknown, Type:Unknown
363588: Aug 7 15:41:45.247: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8203
Channel ID i = 0xA98381
Exclusive, Channel 1
363589: Aug 7 15:41:45.247: //36744/54C358E69A16/CCAPI/cc_api_call_proceeding:
Interface=0x15E3F404, Progress Indication=NULL(0)
I can see that the only difference in the SETUP message between working and not working scenarios is Progress Ind i = 0xA190 - Reserved value in the not working one.
Do you know which Hipath setting is responsible for rejecting this call?