Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

HiPath 3800 not booting after power outage

Status
Not open for further replies.

Suzuki Yota

Technical User
Mar 30, 2020
12
MV
Hi,
We have HiPath 3800 system, which not currently in a boot loop after power outage.
All cards showing red alarm. Below is the output from Serial console. Which keeps repeating. Any idea what happened?

loading FPGA: Load O.K.
testing Checksum Firmware: Test O.K.
testing Data-Bus DRAM: Test O.K.
testing Address-Bus DRAM: Test O.K.
testing Pattern 0x55555555: Test O.K.
testing Pattern 0xAAAAAAAA: Test O.K.
FPGA Registers access: Test O.K.
testing ICGX Registers: Test O.K.
testing PHY identifier value: Test O.K.

Power ON Diagnostics (PODS) has passed

MMC load ..... complete
**************************************************
* CBSAP *
**************************************************
Copyright 2003 Siemens AG

Initialized data of startup
System clock setting
Customer database reset
Reset cause (FW: 0x82) (SUp: 7)
SRAM(bat) OK
Hardware ID : 0x04d0
Serial Number : SK76XXXXXX0834
Parts List Version : -10
Bootrom Version : CBSAP_FW_071126
Ethernet Address 1 : 00:1A:E8:18:45:B8
Ethernet Address 2 : 00:1A:E8:18:45:B9
Count reference (12418) (new)
Start double click (7)
End double click (7)
HW_status (0x30)
CBSAP Exp. Box detected
Testing system interrupt
System interrupt done
Initialize and Test ROSA + MMC
Init ROSA + MMC OK, Test passed
CMS Module present
Start operating system
Application vector loaded
Start watchdog test
Watchdog set on 10 minutes
KDS TRUE lLength = 200000
APS1 TRUE lLength_aps = c00000
WP1 TRUE lLength_wp1 = 100000
STARTUP OFFSET = 200
STARTUP LENGTH = 20a
Aps(0) switch(0) reset(1,0)
Start loading and decompressing
HALT on - startup step: 208 (ddsb200)
- error code/cause: 0 (ddsb201)
- exception no.: 0x301 (ddsb202)


MMC load ..... complete
**************************************************
* CBSAP *
**************************************************
Copyright 2003 Siemens AG

Initialized data of startup
System clock setting
Customer database reset
Reset cause (FW: 0x82) (SUp: 7)
SRAM(bat) OK
Hardware ID : 0x04d0
Serial Number : SK76XXXXXX0834
Parts List Version : -10
Bootrom Version : CBSAP_FW_071126
Ethernet Address 1 : 00:1A:E8:18:45:B8
Ethernet Address 2 : 00:1A:E8:18:45:B9
Count reference (12418) (new)
Start double click (7)
End double click (7)
HW_status (0x30)
CBSAP Exp. Box detected
Testing system interrupt
System interrupt done
Initialize and Test ROSA + MMC
Init ROSA + MMC OK, Test passed
 
Hi Suzuki Yota,

Can you try move MMC and plus in new orther mainboard HP3800? IT done? ( If done, MMC is ok )
It not ok. this mean is firmware on MMC error. You shouble setup firmware for MMC
You must be remove all card on this box ( only keep mainboard ) . Power on and check it.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top