Help....Backup Fail

[pyooi]

Hi, Everybody,

Have anybody face this problem?
The Backup is completed but the status is "Fail"

The Job Log as below




======================================================================
Job server: MPIWEBSVR
Job name: Full_Backup
Job started: July 30, 2003 at 10:00:05 PM
Job type: Backup
Job Log: BEX91.txt
======================================================================

Drive and media information from media mount:
Robotic Library Name:
Drive Name: SEAGATE 1
Slot: 0
Media GUID: {45C8292A-1A01-4145-ACEA-2C796AAC797F}
Media Label: 4MM000005
Overwrite Protection Time Left: None
Append Time Left: Infinite
Targeted Media Set Name: Media Set 1

======================================================================
Job Operation - Backup
Media operation - overwrite.
Hardware compression enabled.
======================================================================

Media Name: "Media created 30/07/2003 10:00:05 PM"
Backup of "D: New Volume"
Backup set #1 on storage media #1
Backup set description: "EWAS Full_Backup"
Backup Type: FULL - Back Up Files - Reset Archive Bit
Backup started on 30/07/2003 at 10:01:37 PM.
File "VDI.LOG" in use - Backed up.
The .DR file required for Intelligent Disaster Recovery is created/updated

Backup completed on 31/07/2003 at 1:24:35 AM.
Backed up 78250 files in 8059 directories.
1 file was in use
Processed 27,529,787,558 bytes in 3 hours, 22 minutes, and 58 seconds.
Throughput rate: 129.4 MB/min
----------------------------------------------------------------------
Unable to attach to MPIWEBSVR.
The item was not found.
^ ^ ^ ^ ^
Unable to attach to MPIWEBSVR.
^ ^ ^ ^ ^

======================================================================
Job Operation - Verify
======================================================================

Verify of "D: New Volume"
Backup set #1 on storage media #1
Backup set description: "EWAS Full_Backup"
Verify started on 31/07/2003 at 1:26:03 AM.

Verify completed on 31/07/2003 at 4:26:41 AM.
Verified 78250 files in 8059 directories.
0 files were different.
Processed 27,529,787,558 bytes in 3 hours, 0 minutes, and 38 seconds.
Throughput rate: 145.3 MB/min
----------------------------------------------------------------------

======================================================================
Job ended: July 31, 2003 at 4:26:41 AM
Job completion status: Failed
======================================================================


Thank you
Regards
pyooi

 

[AdilM]

This is the reason:
Unable to attach to MPIWEBSVR.
The item was not found.
^ ^ ^ ^ ^)

Probably you cannot connect to the server "MPIWEBSVR". May be it's down or the logon information is not correct. Check whether you can browse that server from the "Backup" tab and expand the subdirectories under it. If "MPIWEBSVR" is an old server that long removed from service and no need for taking backup for it, then remove it from the backup selection. Open the properties of that backup job, go to "Selections", select "Text Version" in the "Display" and remove only the reference to "MPIWEBSVR".

 

[pyooi]

Hi AdilM,

Actually, I'm doing the backup in the "MPIWEBSVR" server.
Any Idea?

Regards
pyooi

 

[SQLBill]

According to your job log, you aren't backing it up. Veritas BE says it can't find it:

Unable to attach to MPIWEBSVR.
The item was not found


Why do you think you are backing it up when BE says it wasn't?

-SQLBill

 

[AdilM]

Oh yes, it's the backup server itself. Do you backup more than one drive? I see that the backup of D:\ was ok. Please check your selections, use the "Text Version" and note if there is anything else added there other than D:\*.* /SUBDIR (like another drive, share, Exchange, ...etc)