Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

HBA WWN PROBLEM

Status
Not open for further replies.

mahalingam1

IS-IT--Management
Dec 7, 2007
75
Hi all

I have the following problem with a FC during executing a backup:

When i doing a heavy backup i get the following output in /var/adm/messages:

scsi: [ID 107833 kern.warning] WARNING: /pci@13c,600000/SUNW,qlc@1/fp@0,0/st@w2100001086122290,1 (st68)

SCSI transport failed: reason 'timeout': giving up



This warning appear on all storage nodes of legato with the same wwn.

I have located the HAB port in question:


luxadm -e port

Found path to 5 HBA ports

/devices/pci@1c,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/pci@3c,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/pci@3d,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/pci@13c,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/pci@13c,600000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED


luxadm -e dump_map /devices/pci@13c,600000/SUNW,qlc@1/fp@0,0
Pos Port_ID Hard_Addr Port WWN Node WWN Type
0 10100 0 2100001086122290 2000001086122290 0x1 (Tape device)
1 10300 0 2100001086123198 2000001086123198 0x8 (Medium changer device)
2 10400 0 210000e08b138a93 200000e08b138a93 0x1f (Unknown Type,Host Bus Adapter)


On the library side:


inquire

scsidev@9.0.0:HP Ultrium 2-SCSI F49Z|Tape
S/N: HUP5C00KS2
ATNN=HP Ultrium 2-SCSI HUP5C00KS2
WWNN=FFFFFFFFFFFFFFFF
scsidev@9.0.1:HP Ultrium 2-SCSI F49Z|Tape
S/N: HUL3J05071
ATNN=HP Ultrium 2-SCSI HUL3J05071
WWNN=50060B00001F6EF0
scsidev@9.100.0:ATL M2500 3.07|Autochanger (Jukebox)
S/N: JG0432AHB00025
scsidev@9.100.1:HP Ultrium 2-SCSI F49Z|Tape
S/N: HUL4F02526
ATNN=HP Ultrium 2-SCSI HUL4F02526
WWNN=50060B000028C25A
scsidev@9.100.2:HP Ultrium 2-SCSI F57V|Tape
S/N: HUP7A06CSQ
ATNN=HP Ultrium 2-SCSI HUP7A06CSQ
WWNN=50060B0000FD9D94


My question is how can i relate the HBA WWN on the server with the drive WWN on the library??

Thanks in advance and regards
 
I tend to use these commands:
luxadm probe
luxadm display <path-to-tape> # eg /dev/rmt/0n from 'probe' output


I hope that helps.

Mike
 
HI Mike!!

Thank you very much for you information.

these is i'm looking for


Mahalingam
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top