Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

FMFM outgoing number

Status
Not open for further replies.

koulioumbis

IS-IT--Management
May 21, 2009
421
GR
Team hello.
I have configured FMFM on a BCM450R6 that works great with only one issue.
Does anyone know where to select what number to show when it calls out the 5 numbers?
The application DNs have been programmed to show public OLI a desired number but this does not work.
It shows DID numbers within my DID range but i cannot select where to change it or i do not know where to change it.
i have ISDN30 with 100 DDI numbers.
thanks

Nikos
 
Hello Nikos

I'm not sure how it can be done as the purpose of the Find Me/Follow Me feature is to set it so that the incoming caller dials out on one of the available outgoing routes and as this isn't directly from an extension, then any OLI setting won't be used.

Assuming that the receiving caller needs to see the CLID to know that they might be getting a Find Me/Follow Me call on their phone display would mean a specific number to be shown. I just can't see how it will work unless the BCM 50 system has other trunks that is connected such as analogue ones that could be used instead?.


Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support
 
You cannot use Analog Trunks for FMFM unfortunately.

I dont think you can do anything about the CLID as far as programming from what I can tell.
Seems either the CLID of your SIP/PRI or the originating call is presented and that depends if the carrier overrides (or allows CLID forwarding)

Page 2:

If ALL you sets have OLI programmed with their own DID/DDI and working then all calls to your mobile showing the main number would be FMFM.







________________________________________
We take the time to try to answer your questions for free, please return the favor and take the time to answer back and include any resolution you found elsewhere, thanks.

=----(((((((((()----=

small-logo-sig.png

Toronto Canada
 
yes i agree i can not find anywhere to program special CLID so i fixed it with the PRI provider, so when i send them a 3 digit number that is the application DN range they translate it to the main company PRI number that is better than random DDI numbers.
Regards
Nikos
 
In my Find Me/Follow Me setup, I've configured it so that outgoing calls go via my analogue trunk. The CLID of that trunk is displayed on my phone.


Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support
 
You can configure Find Me/Follow Me to simultaneously ring a maximum of five external
destination numbers. Configured
external destination numbers are
automatically enabled. Analog
trunks are not suppor
ted for outbound calling
"

What am I missing I wonder.


________________________________________
We take the time to try to answer your questions for free, please return the favor and take the time to answer back and include any resolution you found elsewhere, thanks.

=----(((((((((()----=

small-logo-sig.png

Toronto Canada
 
I just tested by changing my outdial number from 94xxx-xxx-xxxx to 91xxx-xxx-xxxx (94 is my SIP & 91 is my Analog Trunk)
Monitor didnt even flinch.

I am curious now more than ever.

________________________________________
We take the time to try to answer your questions for free, please return the favor and take the time to answer back and include any resolution you found elsewhere, thanks.

=----(((((((((()----=

small-logo-sig.png

Toronto Canada
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top