Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Firmware Download to a 3904.
- Thread starter Don6531
- Start date
bhassell2000
Technical User
you can try FDLC to cancel the download and then FDLU X X X X to start the download again
Thanks,
Buddy
Linked in Profile
Thanks,
Buddy
Linked in Profile
Firebird Scrambler
Systems Engineer
Details:
Unable to access any overlays on call server, OVL306 given on TTY. This was the result of a failed FDLU to an M3903 telset in my case, I suspect pertinent to all M3900 range of phones however.
After accessing load 32 by using the suspension command and an FWVU is run against the affected TN you get 'PSDL IS NOT IDLE' message
Fix:
Use the suspend command to access ld 32, use fdlc to cancel the suspended command, disable & enable the affected card and re-commence a subseqent FDLU.
This time, in my case, the download was successful.
#############################################################
Useful Tip for 7.5 Systems
The following versions of up-issued firmware for the M3900 series of digital phones are now Generally Available:
M3903 version 9.0
M3904 version 9.3
M3905 version 9.3 version 9.4 now being shipped on Rls 7.5 sites
See Nortel Technical Bulletin 2009009684, Rev 2 for full details
-----------------------------------------------------
Important Note for upgrades to CS1000 rls 6
-----------------------------------------------------
It is recommended for all CS1000 customers upgrading to rls 6.0 to have their M3900 sets upgraded to the latest firmware version prior to the core upgrade. Failing to do so will cause problems with M3900 sets during Transfer call scenarios.
A fix for CR (Q01805423-01: 390x during a transfer call have no 'Conf' softkey) was introduced, this fix
contains changes in both core and Taurus firmware, if CS1000 system is upgraded to rls 6.0 without upgrading M3900 sets then during the transfer scenario, after the second leg of the call is answered the connect key will not appear.
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
Unable to access any overlays on call server, OVL306 given on TTY. This was the result of a failed FDLU to an M3903 telset in my case, I suspect pertinent to all M3900 range of phones however.
After accessing load 32 by using the suspension command and an FWVU is run against the affected TN you get 'PSDL IS NOT IDLE' message
Fix:
Use the suspend command to access ld 32, use fdlc to cancel the suspended command, disable & enable the affected card and re-commence a subseqent FDLU.
This time, in my case, the download was successful.
#############################################################
Useful Tip for 7.5 Systems
The following versions of up-issued firmware for the M3900 series of digital phones are now Generally Available:
M3903 version 9.0
M3904 version 9.3
M3905 version 9.3 version 9.4 now being shipped on Rls 7.5 sites
See Nortel Technical Bulletin 2009009684, Rev 2 for full details
-----------------------------------------------------
Important Note for upgrades to CS1000 rls 6
-----------------------------------------------------
It is recommended for all CS1000 customers upgrading to rls 6.0 to have their M3900 sets upgraded to the latest firmware version prior to the core upgrade. Failing to do so will cause problems with M3900 sets during Transfer call scenarios.
A fix for CR (Q01805423-01: 390x during a transfer call have no 'Conf' softkey) was introduced, this fix
contains changes in both core and Taurus firmware, if CS1000 system is upgraded to rls 6.0 without upgrading M3900 sets then during the transfer scenario, after the second leg of the call is answered the connect key will not appear.
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
- Status
Similar threads
- Question
- Locked
- Question
- Locked
- Question
- Locked
- Question