EXNOPU LENGTH

[cuneyt2919]

Hi
Is it possible to change exnopu length to 11 digit? Is there any patch for it or sth else to do it so..
I can not set an 11 digit number 03124589100 to our telecom route.
Please help me...

 

[rfpui]

Why you must send so long number?

 

[cuneyt2919]

Because telecom wants it.. Telecom says, if i don't set a number on DID range which telecom assigned to our trunks we can not make an outbound call, Telecom assigned us 03124589100 03124589199..
I should do it as soon as possible..

RONDI CPDNI ,etc doesn't work as the workers are on other location.. RONDI and CPDNI doesn't affect to the workers. I should do it as soon as possible. But if i give an 11 digit exnopu, i can assign it to the interconnection line of the other switch, which the staff are configured, then it's possible.

 

[rfpui]

is your internal number series 100 to 199?

 

[cuneyt2919]

No. Internal number series (extension numbers) are 1000 to 4999. And it's not on the same location of telecom PRIs We do not use the DID numbers of this 90 ports and we only use it for inbound calls to call center and outbound calls for local pay on same city. I mean these DID numbers are not assigned to staff...

 

[rfpui]

Now I know more about Your problem
And I thing that solution is to use NUTRx

Call Center is MD 110 side A
Connection to telecom is MD 110 side B
Is it correct?

If yes you use ROUT to connect from A to B
Some digit are send from A to B to connect to external number from B to telecom

In site B try to set number conversion
NUTRI:ENTRY=xxxxx,CNVTYP=1,NUMTYP=10,PRE=yyyyy,TRC=zzzzz;
Xxxxx – are digits received by site B from A

PRE=yyyyyy
The parameter states the digits to be inserted in front of the number at number conversion.
- For sent A/connected number, the number of digits in the parameter can be up to 20.
- For received B-number and received A/connected number, the number of digits in the parameter can be up to 10. TRC=zzzzzzThe parameter states the number of leading digits to be truncated from the number. - For sent A/connected number, the maximum value of the parameter can be 20.
- For received A/connected number and B-number, the maximum value of the parameter can be 20.

My be it is solution but I’m not sure
Good luck

 

[cuneyt2919]

Hi,
I changed the nutri ... received A number such as
My extension is 4061 i'm in site A

I configured these on site B
<nutri:ENTRY=4,TRC=4,CNVTYP=1,NUMTYP=10,PRE=3124589100;
NOT ACCEPTED
PRE
NOT IN RANGE

When i change it to

<nutri:ENTRY=4,TRC=4,CNVTYP=1,NUMTYP=10,PRE=458;
EXECUTED


But it doesn't affect to site A extensions.It doesn't send any number to telecom, but if i change my extension ADC parameter, then while calling outside via B site, the A number is 04061...
I mean nutri on site B doesn't effect to site
Also i tried

nutri:ENTRY=4,TRC=4,CNVTYP=2,NUMTYP=6,PRE=3124589100;
nothing changed... Again it sends either the extension number 4061 or no number due to ADC parameter of extension

The connection between A site and B site is Qsig.. A site is VERSION=LZY2035151/6/BC10C144/R6A and B site is VERSION=LZY2035101/1+CNI75/R1A

Thanks for your help..

 

[rfpui]

It is a problem
B site is BC9 and with this version
PRE

- For sent A/connected number, the number of digits in the parameter can be up to 5.

- For received B-number and received A/connected number, the number of digits in the parameter can be up to 10.

have you ALEX?

 

[cuneyt2919]

Yes i have dynatext -same as alex-
but the problem is, even i enter 5 digits for PRE , it is also not be seen on PSTN network. it only shows the extension number of BC10 site A or nothing to show.

 

[rfpui]

Hi
I’m still thinking about Your problem

Next proposition is to mix NUTRI in Side A and B

For example change sending number from A to B

Side A
NUTRI:ENTRY=4,CNVTYP=1,NUMTYP=11,trc=4,PRE=89100;
Or
NUTRI:ENTRY=4, CNVTYP=1,NUMTYP=11,trc=4,PRE=89100,ROU= Qsig route to B;

Side B
NUTRI: ENTRY=89, CNVTYP=2,NUMTYP=6,PRE= 31245;
Or
NUTRI: ENTRY=89, CNVTYP=2,NUMTYP=2,PRE= 31245;

 

[cuneyt2919]

Hi
2 days ago an expert came from Ericsson solution center Austria, we checked it together and he told that he would simulate the problem in his lab.
But as far as i know, the nutri on B side affects only the subscribers in B exchange. As the B exchange is a transit exchange, nutri doesn't affect the transit calls...