Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations IamaSherpa on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

%Error opening tftp://255.255.255.255/*******

Status
Not open for further replies.

Up

MIS
Oct 31, 2000
9
US
I am wondering what these error messages represent with respect to my Cisco 2501 Router.
System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 16384 Kbytes of main memory

F3: 6799388+89240+456028 at 0x3000060

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-D-L), Version 12.0(9), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Co22:06 by bettyl
Image text-base: 0x030387D0, data-base: 0x00001000

cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of memory.
Processor board ID 03255035, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read ONLY)

%Error opening tftp://255.255.255.255/network-confg (Timed out)
%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
%Error opening tftp://255.255.255.255/robert1-confg (Timed out)
%Error opening tftp://255.255.255.255/robert1.cfg (Timed out)
ed!


00:00:37: %SYS-5-CONFIG_I: Configured from memory by console
00:00:37: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:37: %LINK-3-UPDOWN: Interface Serial0, changed state to down
00:00:37: %LINK-5-CHANGED: Interface Serial1, changed state to administratively
down
00:00:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta
te to up
00:00:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state
to down
00:00:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state
to down
00:01:37: %SYS-5-RESTART: System restarted --
Ciscorating System Software
IOS (tm) 2500 Software (C2500-D-L), Version 12.0(9), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 24-Jan-00 22:06 by bettyl

If you need the configuration of Cisco 2501 let me know.

Thank You
Robert
 
mbhandari has a good site there for you to look at, however I'm curious if your intentions are to load from a tftp server are from the router itself? If its from a tftp
you need to type in ( boot system tftp filename ip address ). Without this it should boot from the first image it finds in the router. #-) Good Luck !!!
 
I got the same errors when I tried to upgrade my router code for the first time. It turned out that the problem was a simple setting in the config.

This is how I fixed it:

Enter configuration mode put in

config-register 0x2102


Let me know if this helps,

bmorritt
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top