Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

DX150R Replace system card

Status
Not open for further replies.

fadge

Technical User
Apr 8, 2009
7
GB
Hi!
I have a DX150R running V8 and we had a lightening strike a few weeks ago which trashed the card to the point it would not even boot to smi.

I have bought a replacement of the same rev. but it was from a duel processor DX and the Nival.dat is set to 1.0 and not 0.0 so I cannot FTP the config on to it as when smi loads it has to nival to load setting from and when i ping from it to my pc, or any address for that matter, I get host unreachable. In fact it will not even ping it's own address. The link lights are on the system card and the PC and to iliminate any other causes I have connected the 2 dirtect with a X over cable.

Can anyone offer any advice on how I can resolve this?

Thanks

Fadge
 
First things first, unless you have already checked.

Switch 1 on the card elements 1, 2, 3 should be 1=on, 2=on, 3=off,
this tells the card it is a single processor.

Check the the Mac addresses on the card and write them down, (there should be x 2)

Next connect to the v24 at 9600bd put switch 9(little switch at the top into the down position and press the reset button at the top leaving switch 9 in manual.

The card will then load and come back with some thing like this:-

DX SYSTEM MAINTENANCE INTERFACE
01/09/06 09:59 Firmware Version:0.206 Application Version:2.0.22 Release ACTIVE
SMI A>
Type se and you will then see the environment similar to this:-

FPGA=0.0/fpga2009.a
DSPFILE=0.0/dsp0109.a
MUSICFILE=0.0/music02.a
SER1=9600
SER2=1200
SER3=9600
SER4=9600
CUST=3
CIL=2
REMOTE=4
IPACT=10.18.16.4,ffffff00
ETHACT=08:00:06:9E:d5:7a
MEDETHACT=08:00:06:9E:d5:7b
MODEM_STRING=TQ1S0=1+MS=9\n\r
AUTO=0.0/fhpsf481.app
NIVAL=0.0/ni.dat
SMI A> dir

1, Check the ETHACT/MEDETHACT addresses are correct, (Mac addresses).
2. Over write the IPACT statement by using:- se IPACT=xxx.xxx.xxx.xxx,(subnet mask in hex).
3. Over write the AUTO Statement :- se AUTO=0.0/xabcd567.app what ever your software is.
4. Delete NIVAL, se NIVAL=

5, Press reset and list again to check all is correct.

While in SMI list the directory it should be something like this:-

SMI A> dir
DIRECTORY LISTING OF 0.0FILENAME TIME DATE BYTES
==========================================

DATABASE.INI 02:16 21/11/05 383
dsp0109.a 07:47 25/08/05 117276
DUMP.1 13:37 22/08/06 1893152
fhpsf481.hrm 06:00 30/08/06 1893220
TEST.DAT 00:00 01/09/06 1024
fhpsf481old.app 01:48 21/11/05 150
sys20022.scx 01:57 21/11/05 2405332
sys00022.scx 07:47 25/08/05 2355890
fhpsf481.app 01:55 21/11/05 150
fpga2009.a 07:47 25/08/05 503424
music02.a 07:47 25/08/05 262208
snmp.ini 07:47 25/08/05 433
tone0002.a 07:47 25/08/05 744968
cniuhold.mus 07:47 25/08/05 267451
sys20014.scx 07:48 25/08/05 2392455
TOTAL - 12,837,516 Bytes(s)
FREE SPACE - 45,750,272 Bytes(s)
SMI A>

Now try pinging the IP address with a cross over,

Assuming you have a back up of your old config you need to delete the file xxxxx890.app,
and any other files not needed,
Dos commands = DEL xxxxx890.app from the v24 port + xxxxx890.hrm.

Log onto Telnet BUT with without a password,(you have deleted NIVAL) this can but put back later.

If this works FTP your config backups to 0.0 xxxxx890.hrm/xxxxx890.app.

If you get this far let me know and we will see if we can get further on.

Mal.
 
Thanks!

It was the mac address's.

When I entered the ones on the card in SE I was able to get in and FTP the files over. The only problem i have now is that i cannot FTP from the DX to my PC and get the error below:

dosfslib: ILLEGAL FILENAME

I am using procom plus.

Thanks again

Fadge
 
Fadge,

Try using ws_ftp95, its what most Realitis/dx engineers use, download from:-


Set Host type to either Microsoft NT or Automatic, leave port at 21.
You will have 2 x windows, left one is local, right Host.
Its then just a matter of highlighting the files required and using the left/right transfer buttons.

When telneting to a dual processor, drive 0.0 is accessed first(Ram on card) you can then change to the media card by changing directories to 1.0 and back to 0.0.

Also do not forget the NIVAL command, if you removed this from the environment statement you do not require a password.
if NIVAL is still present the password is either ... realitis .... or .... REALITIS these can only be checked after the system is loaded by using the lnic command.

Mal.
 
If that does not work for you - you can use a DOS window.
ftp
open 10.18.16.4
bin
hash
put 'filename'
(filenames are case sensitive)
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top