lanpham_imported
Technical User
Hi, everyone!
My MD system has got a Lim. This Lim is running one side. Now, I want to creat a Duplicated control system.
I entered the command as below:
DCSYI:LIM=1;
STANDBY CONTROL SYSTEM INITIATION REUSULT
LIM EXCUTED
Then dump the system.
After dumping, the system can't load the standby side. There is a alarm:
CLASS: 4
72 LOADING OF STANDBY SIDE HAS FAILED
DATE TIME ALP NOIF EQU INF1
16NOV18 16:20:19 5 2 001-*-**-** 50
CLASS: 3
85 BUFFER TRANSFER HAS FAILED
DATE TIME ALP NOIF EQU INF1 INF2 INF3 INF4
16NOV18 16:16:34 1 6 001-0-**-** 390 11 1 250
74 STANDBY SIDE FAULTY
DATE TIME ALP NOIF EQU
16NOV18 16:19:36 3 1 001-*-**-**
79 STANDBY SIDE NOT LOADED
DATE TIME ALP NOIF EQU
16NOV18 16:19:47 4 1 001-*-**-**
And with DCSSP command:
DCSSP;
CONTROL SYSTEM INFORMATION
LIM CSSIDE A CSSIDE B BLOCKWORD
1 EXECUTING BLOCKED B'00001100
BLOCKWORD:
B0= MANUAL
B1= FAULTMARKED
B2= SYSTEM
B3= UNLOAD
B4= INTERNAL
B5= LOADBLOCK
B6= NO CONTACT
B7= VACANT
END
Although i entered DCLDI:LIM=1;
My mask only reads 50 number on the standby side. In the DynaText document says that:"The LIM disposition table is being loaded" for that!
Can someone give me any advise!
Thanks!
My MD system has got a Lim. This Lim is running one side. Now, I want to creat a Duplicated control system.
I entered the command as below:
DCSYI:LIM=1;
STANDBY CONTROL SYSTEM INITIATION REUSULT
LIM EXCUTED
Then dump the system.
After dumping, the system can't load the standby side. There is a alarm:
CLASS: 4
72 LOADING OF STANDBY SIDE HAS FAILED
DATE TIME ALP NOIF EQU INF1
16NOV18 16:20:19 5 2 001-*-**-** 50
CLASS: 3
85 BUFFER TRANSFER HAS FAILED
DATE TIME ALP NOIF EQU INF1 INF2 INF3 INF4
16NOV18 16:16:34 1 6 001-0-**-** 390 11 1 250
74 STANDBY SIDE FAULTY
DATE TIME ALP NOIF EQU
16NOV18 16:19:36 3 1 001-*-**-**
79 STANDBY SIDE NOT LOADED
DATE TIME ALP NOIF EQU
16NOV18 16:19:47 4 1 001-*-**-**
And with DCSSP command:
DCSSP;
CONTROL SYSTEM INFORMATION
LIM CSSIDE A CSSIDE B BLOCKWORD
1 EXECUTING BLOCKED B'00001100
BLOCKWORD:
B0= MANUAL
B1= FAULTMARKED
B2= SYSTEM
B3= UNLOAD
B4= INTERNAL
B5= LOADBLOCK
B6= NO CONTACT
B7= VACANT
END
Although i entered DCLDI:LIM=1;
My mask only reads 50 number on the standby side. In the DynaText document says that:"The LIM disposition table is being loaded" for that!
Can someone give me any advise!
Thanks!