Diverting External incoming call to QSIG route

[AntBan]

Hello,
I'm having trouble diverting a call incoming from external ISDN route to a station on a different PBX interconnected via QSIG to my MD110. Any help appreciated.

My system is BC12 SP5
Note this is a eurpean box (E1)
ISDN route:
rocap:rou=101;
ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

101 7110000000000010 5 2110030000 0 30 128 03151515 111110000031 111111

END

<rodap:rou=101;
ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

101 SL60 H'00000310 H'05400000 H'06400000 NO

END

<roddp:dest=40;
EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
40 101 1707000000000250107001101 0 1 0


QSIG route:
<rocap:rou=100;
ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

100 7110000000000010 5 2110030000 0 30 128 03151515 111110000031 111111

END

<rodap:rou=100;
ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

100 SL60 H'00000310 H'55440000 H'06300000 NO

END

<roddp:dest=42;
EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

42 100 1707000000000250107001100 0 1 0

<nadap;
NUMBER ANALYSIS DATA

TYPE OF SERIES NUMBER SERIES

EXTENSION NUMBER SERIES 1001 - 1199
4500 - 4508

EXTERNAL DESTINATION CODE 21
25
31 - 38
40
42
550 - 560
650
666
950

OWN EXCHANGE NUMBER SERIES 777

TYPE OF SERVICE CODE SERVICE CODE

EXTERNAL NUMBER LENGTH DATA

EXTERNAL NUMBER NUMBER LENGTH

40 4 - 4
42 4 - 4
550 4
551 3
554 4 - 10
650 10 - 10
666 3 - 7

PROCEED TO SEND SIGNAL DATA

EXTERNAL NUMBER POS. TYPE

CALL DISCRIMINATION DATA

EXTERNAL/INTERNAL NUMBER CAT


END

cdidp:dir=1154;
CALL DIVERSION INDIVIDUAL DATA

DIR DIV

1154 4200


susip:dir=1154;
STATUS INFORMATION AT 16:51:52 09SEP05

DIR TYPE TRAFFIC STATE/PTR LINE STATE/PTR DIV STATE ADD INFO

1154 DTS IDLE #027C FREE #03CA BSY,NAN
ODN1:IDLE
ODN2:IDLE
ODN3:IDLE

END


THx
Tony

 

[HIREI]

Hello, what the trouble is?

Do your have protocol analyzer? Or you can monitor by MD110 commands, and then use SAM tools (Decoder).

 

[AntBan]

Hello HIREI,
Basically, A call comes into the MD110 via an ISDN PSTN route (route 101)for station 1154. Station 1154 is set for follow-me to another PBX station (Cisco Callmanager IP phone) that is interconnected to the MD110 via a QSIG trunk (route 100). The call is never forward to the IP phone, MD110 (route 100) disconnects the call after 10 seconds of idle Call Proceeding state. I am wondering if there is a nother way to CF a incoming PSTN call.
Note:
If the call is made to 1154 from a local station or a IP phone from the callmanager side the CF is successful.

A trace of the PSTN call is below
14:13:27/110.6 2- TS D1 BOP FRAME [0050]
D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:003 NS:003 [0046]
D3 QSIG Pro:08 RefO,00 0a) SETUP
IE0/a1) len:0 >> Sending complete
IE0/04) len:3 >> Bearer capability
Oct 3 : -00----- Coding = ITU-T
---00000 Capability = Speech
Oct 4 : -00----- Transfer mode = Circuit
---10000 Transfer rate = 64 Kbit/s
Oct 5 : -0100011 L1 protocol = G711 A-law
IE0/18) len:3 >> Channel identification
Oct 3 : -0------ Interf ID = Implicit
--1----- Interface = Primary
----1--- Preferred/Exclusive = Exclusive
-----0-- D-chan ind = not D-channel
------01 Channel select = Indication follows
Oct 32: -00----- Coding = ITU-T
---0---- Number/Map = Number
----0011 Type = B-channel
Oct 33: -0000001 Channel number = 1
IE0/28) len:13 >> Invalid/unknown IE code
42 6f 66 6f 20 42 61 75 74 69 73 74 61
IE0/6c) len:6 >> Calling party number
Oct 3 : -010---- Type of number = National
----0001 Numbering plan = ISDN (E164)
Oct 3a: -00----- Presentation = Allowed
------01 Screening = User, verified/passed
Oct 4 : ******** Number = 4001
IE0/70) len:5 >> Called party number
Oct 3 : -010---- Type of number = National
----0001 Numbering plan = ISDN (E164)
Oct 4 : ******** Number = 1154
14:13:27/118.8 2- RS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:004
14:13:27/174.5 2- RS D1 BOP FRAME [0014]
D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:004 NS:003 [0010]
D3 QSIG Pro:08 RefD,00 0a) CALL PROCEEDING
IE0/18) len:3 >> Channel identification
Oct 3 : -0------ Interf ID = Implicit
--1----- Interface = Primary
----1--- Preferred/Exclusive = Exclusive
-----0-- D-chan ind = not D-channel
------01 Channel select = Indication follows
Oct 32: -00----- Coding = ITU-T
---0---- Number/Map = Number
----0011 Type = B-channel
Oct 33: -0000001 Channel number = 1
14:13:27/178.9 2- TS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:004
14:13:32/308.0 1- TS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:0) RR P/F:1 NR:009
14:13:32/312.4 1- RS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:0) RR P/F:1 NR:009
14:13:37/027.7 2- RS D1 BOP FRAME [0013]
D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:004 NS:004 [0009]
D3 QSIG Pro:08 RefD,00 0a) DISCONNECT
IE0/08) len:2 >> Cause
Oct 3 : -00----- Coding = ITU-T
----0001 Loc = Private net to local usr
Oct 4 : -0010000 016 = Normal clearing
14:13:37/032.5 2- TS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:005
14:13:37/046.1 2- TS D1 BOP FRAME [0009]
D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:005 NS:004 [0005]
D3 QSIG Pro:08 RefO,00 0a) RELEASE
14:13:37/053.2 2- RS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:005
14:13:37/072.2 2- RS D1 BOP FRAME [0009]
D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:005 NS:005 [0005]
D3 QSIG Pro:08 RefD,00 0a) RELEASE COMPLETE
14:13:37/077.5 2- TS D1 BOP FRAME [0004]
D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:006


Thx
Tony

 

[HIREI]

Hello,
1) to reroute call you may use ADCOI: NANSE:for 1154 (EX), NANSI for 1154 (AC), ABB=1154, TRA=4200;

2) can you call to 4200 directly?

3) where SETUP with number 4200 ?

 

[AntBan]

Hello HIREI,
Thank you very much for your assistance, I really appreciate you helping me.

1) I tried NANSE to remove ex 1154 and initiated 1154 as AC, but my command line gave me the following error.
<NANSE:numtyp=ex,numse=1154;
NANSE:NUMTYP=EX,NUMSE=1154;

SURE? (YES/NO)
<yes
NOT ACCEPTED
NO REMOVAL ALLOWED

I guess this is a license limitation on my box. Have you seen this issue before, or maybe I entered the command wrong?

2) I can make a direct call from any 11XX station to 4200, including 1154.

3) No set-up is ever sent to 4200. the QSIG leg between 1154 and 4200 remains idle.

I might have an idea of what the problem is. The leg I am using for PSTN ISDN was used for QSIG before, this leg was set for reroute on diversion, obviously the PSTN does not do reroute and should forward switch the CF but I have not been able to disbale reroute on either leg. Could this be the problem? Do you know how to disable reroute on diversion for the entire PBX or each route?
Again thank you very much.
Tony

 

[HIREI]

Hello,
did you EXTEE or KSEXE for 1154 before NANSE?

 

[AntBan]

Hi HIREI,
I used KSEXE and then the other commands recommended by you. I succesfully got the call to foward out to the QSIG trunk. This is GREAT!!

THanks a lot for your help

 

[AntBan]

Hi HIREI,
Another question for you. Is there anyway to forward a call using abbreviated dialling without ksexe the station?

We want to provide an easier way for the user to forward the call to the other building. We don't want to remove a station each time an engineer needs to go to a different building.

Thx
Tony

 

[AntBan]

Hi again HIREI,
Sorry to kep sending you so many questions.
Is there anyway to disable reroute on diversion (cdini, internal follow me)
Thx

 

[HIREI]

Hello,
for example, when the engineer needs to go to a different building, he/she can use the procedure external follow me: *22# ext.number# (CDIV=001130000 (D3=1 allows it).

"Is there anyway to disable reroute on diversion (cdini, internal follow me)?"

cdini / cdine:dir=...; what do you mean?
internal follow me - IMHO, only by internal parameter station change.