Disconnection Tone

[fallenangel1]

I need to configure Disconnection Tone in my CS1000E. I have done it before and tried to repeat the same procedure, i.e, LD 56, chg, FTC, TLP, XTON 007, XCAD 016, TLPT 10.

I have tried repeating the same tone and cadance codes defined for Busy tone. I tried edd after that and even restarting my system but nothing happened. Any idea what to do?

 

[fallenangel1]

Forgot to give my LD 56 print:

>ld 56
FTC000
TBAR000
FDTD000
DTAD000
AANN000
MEM AVAIL: (U/P): 98885340 USED U P: 5306855 77626 TOT: 104269821
DISK SPACE NEEDED: 106 KBYTES
REQ prt
TYPE ftvc


SCH101

TYPE ftc
TABL 0
USER yes

TYPE FTC
TABL 0
NCAD 001
NBCS
XTON 002
DCAD 002
DBCS
XTON 002
ICAD 005
IBCS
XTON 002
RCAD 001
RBCS
XTON 002
GCAD 001
GBCS
XTON 002
HCAD 003
HBCS
XTON 002
PCAD 001
PBCS
XTON 000
XCAD 000
NDR1 PBX 002
NDR1 BCS
XTON 002
XCAD 002
NDR2 PBX 002
NDR2 BCS
XTON 002
XCAD 002
NDR3 PBX 002
NDR3 BCS
XTON 002
XCAD 002
NDR4 PBX 002
NDR4 BCS
XTON 002
XCAD 002
DIAL
XTON 004
XCAD 000
SPCL
XTON 004
XCAD 000
CDT
XTON 004
XCAD 000
CFDT
XTON 004
XCAD 016
MWDT
XTON 004
XCAD 017
CFMW
XTON 004
XCAD 018
BUSY
XTON 007
XCAD 016
RGBK
XTON 005
XCAD 031
ARBK
XTON 011
XCAD 002
FFCT
XTON 004
XCAD 000
ACTN
XTON 004
XCAD 000
HOWL 0027
LIMT
XTON 009
XCAD 002
NRMT
XTON 009
XCAD 018
AWUT
XTON 007
XCAD 017
OVFL
XTON 007
XCAD 017
TEST
XTON 008
XCAD 000
ERWT
XTON 003
XCAD 000
ACFT
XTON 003
XCAD 000
TLP
XTON 007
XCAD 016
TLPT 30
PATI
XTON 007
XCAD 016
EEST
XTON 003
XCAD 000
ILIN
XTON 056
XCAD 002
ILOU
XTON 034
XCAD 002
CFWT
XTON 003
XCAD 000
CAMP
XTON 003
XCAD 000
CDNC 017
ACBT
XTON 003
XCAD 000
CDNC 019
AOBT
XTON 003
XCAD 000
CDNC 018
CAB
XTON 043
XCAD 019
CDNC 019
INTU
XTON 003
XCAD 000
CDNC 019
CWT
XTON 003
XCAD 000
CDNC 020
OBKT
XTON 003
XCAD 000
CDNC 017
OVRD
XTON 003
XCAD 000
CDNC 018
OHQ
XTON 003
XCAD 000
CDNC 003
SRT
XTON 003
XCAD 000
CDNC 021
TMAT
XTON 003
XCAD 000
CDNC 022
TMOT
XTON 003
XCAD 000
CDNC 023
TSUT
XTON 003
XCAD 000
CDNC 023
ABST
XTON 004
XCAD 000
CDNC 208
PNNC
XTON 000
XCAD 000
CDNC 000
SRC1
XTON 000
XCAD 000
SRC2
XTON 000
XCAD 000
SRC3
XTON 000
XCAD 000
SRC4
XTON 000
XCAD 000
SRC5
XTON 000
XCAD 000
SRC6
XTON 000
XCAD 000
SRC7
XTON 000
XCAD 000
SRC8
XTON 000
XCAD 000
CFSN
XTON 004
XCAD 000
CPOQ
XTON 003
XCAD 000
RGAR
XTON 004
XCAD 000
RPCT
XTON 004
XCAD 000
RGAB
XTON 007
XCAD 000
MWAN
XTON 004
XCAD 000
DNDA
XTON 004
XCAD 000
SSLK
XTON 004
XCAD 000
P10 8
ID1 768
ID2 512
IDD 512
IDE 384
RVDL 0

*** THE USERS OF TONE TABLE 0 ARE:***

CUSTOMER 00
CUSTOMER 00 ROUTE 012
ROUTE 013
ROUTE 021
ROUTE 031
ROUTE 088
ROUTE 100
ROUTE 101
DISK SPACE NEEDED: 106 KBYTES
REQ ***

 

[fallenangel1]

any clue?

 

[GHTROUT]

I'm not sure, but the system may let you configure this even if is did not have "Flexible Tone and Cadences (FTC) package 125" turned on

The result is it just might not work if the package isn't there.

I'd check LD 22 REQ PRT PKG



--
GHTROUT.com - Help for Nortel Meridian/CS1000 System Administrators
--

 

[fallenangel1]

checked LD 22 PCKG, its there on the list.

 

[fallenangel1]

Changing the FTC values are enough? I mean is there any procedure to apply it, like INI or Resetting DTRs?

 

[fallenangel1]

yet another help call. I am badly stuck in this issue.

 

[NoypiToits]

Quick question...Is your system setup to "Mu Law or Alaw"?

 

[fallenangel1]

A-Law..

Go For It Even If It's Impossible !

 

[fallenangel1]

Does it make any difference Villa?

Go For It Even If It's Impossible !

 

[NoypiToits]

yes, because all your xton are in mulaw. Change all xton 003 to xton 130 and 004 to 129. But before you do that, change 1 particular xton (TLP XTON = 130 TLPT = 10) that you want to test.

Regards,
Villareal

 

[fallenangel1]

changing the system to Mu-Law will solve the problem, or, conversely, changing XTON of TLP to 130, TLPT to 10 will solve the problem, is that what I should understand?

I am stuck in this issue. Thank you very much for your responses.

Go For It Even If It's Impossible !

 

[fallenangel1]

I tried changing TLP to 130 and TLPT to 10, didnt change already set A-Law. Nothing happened.

Go For It Even If It's Impossible !

 

[fallenangel1]

I just checked and found that companding law of my system was MU Law.... Any clue Villareal?

Go For It Even If It's Impossible !

 

[fallenangel1]

Its strange, and more strange thing that I couldnt get answer of this very issue. I changed my system to A-law frm Mu-law. Tried changing values in A-Law format (129 XTON, 30 XCAD)... Changed it back to Mu-Law, tried again to Mu-Law values (XTON 4, XCAD 2)..
Have tried LDTA as well... still nothing. What else can be the issue? I am badly stuck with this problem...

Go For It Even If It's Impossible !

 

[NoypiToits]

cHANGING FROM aLAW TO mULAW OR vise versa needs a sysload to take effect..

Villareal

 

[fallenangel1]

I performed an EDD and restarted the system. It changed to A-Law successfully. I can show you the captures as well.

Go For It Even If It's Impossible !

 

[NoypiToits]

Please print and check Alaw Configuration

LD 17 (Parm)
PCML = A

LD 17 (ATRN)
CODE = 2

LD 97 (SYSP)
INTN = yes

LD 97 (XCTP)
DTMF = 138

Villareal

 

[fallenangel1]

I was using LD 97 (XCTP), DTMF = 14 rather then 138. Have changed my system back to Mu Law since nothing happened at A-Law. I will give it a try again if you suggest it can effect positively. Thanks for helping me..

Go For It Even If It's Impossible !