digital FCT 2N Enterprise!

[rfpup]

Hi to all,

I have to connect a digital FCT 2N Enterprise with the MX-one TSW sp2 using TLU79 card.

As explained in the manual of FCT, there are two possible scenarios for connection:
1. PSTN network ---> NT terminal ---> PBX (as TE) ---> PBX (as TE)---> FCT (as NT)

2. PSTN network ---> NT terminal ---> PBX (as TE) ---> PBX (as NT)---> FCT (as TE)

I am using two TLU79 cards; one for connecting to PSTN and the other to FCT.

I am trying with the following configuration but SLIP alarms are appeared
[tt]rocap:ROU=120;ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
120 7110000000000010 5 3100000001 0 30 128 00151515 211110000030 111100

END

<rodap:ROU=120;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
120 SL60 H'00000214 H'15500000 H'06410000 NO

END

<roddp:dest=068;EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
068 120 00050000000002501000000010 0 1 0 [/tt]
Which of the versions above is supported from MD?
Any other idea about how to program MD?

thank you

 

[whosrdaddy]

you must use case (2) to avoid slip problems.

prog is ok, just use 06310000 as VARO (MD = NT)

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[rfpup]

thank you whosrdaddy for your support.

Slip is avoided with your configuration, trunks are open but I can not make calls.
I have line blocked in the display of the digital telephone.
Call goes up to GSM gateway seen from the tracing file of GSM gateway.

any other idea would be helpful.

 

[whosrdaddy]

make sure your fct is configured as TE.
TLU79 can block sometimes
do a RFBOI:BPOS=x-x-x; and a BLDBE:BPOS=x-x-x,ALLFM=YES;

if problem persists you have a cabling problem.

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[rfpup]

The current version of the firmware of the FCT I am using, use TE port as synchronization port from NT connected to PSTN.
I tried to give synchronization from:
a. PSTN but still there are SLIP alarms in MX-one TSW

b. From a free port of the TLU79 (not the one connnected for trafic) but I still have alarms. SLIP alarms are rare but there are the following alarms
[tt]CLASS: 0
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
21MAY07 14:15:06 5 1 SLP60 001-2-70-02 58 7 5
RDATE RTIME
21MAY07 14:15:21
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
21MAY07 14:15:21 6 1 SLP60 001-2-70-02 58 7 26
RDATE RTIME
21MAY07 14:15:43
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
21MAY07 14:15:43 7 1 SLP60 001-2-70-02 58 7 6
RDATE RTIME
21MAY07 14:17:49
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
21MAY07 14:18:00 10 6 SLP60 001-2-70-02 58 7 7
RDATE RTIME
21MAY07 14:18:00[/tt]

I also have all the cards of the magazine 2 restarted.

Any other idea ?

Thanks