Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Difference between LUVU and LUDU

Status
Not open for further replies.

HVehari

Technical User
Sep 4, 2003
42
SA
Hi,
In option 11C, when printing unused TN in REQ: prompt we write
LUVU for voice units and LUDU for data units. Which TN we have to select to program 3902 set I mean from LUVU list or LUDU list?

Also I like to know how to Create (not Copy) new DN from unused TN step by step.



Thanks and regards,
HVehari

 
It is not clear what LUDU shows?

HVehari
 
in LD 20 at REQ type LUDN for List Unused Directory Numbers.
you can put in a lead digit when you arrow down to DN if you know what you want your new ext to start with. Then, once you have your TN (LUVU) do REQ NEW, TYPE 3902, TN x-x-x-x, and just fill in each prompt as it comes up. easiest thing to do (why don't you want to copy?) is to print an existing 3902 and enter the same values for the new one. good luck.
 
The last answer should be enough.

If you List your Un-Used DN's, be sure you know your DID Range, if you REQ: PRT, TYPE: LUDN, enter, enter, enter until all your Un-Listed DN's appear your switch will show all Un-Used DN's available, you need to know your DID range.

If you know the TN of a known good 3902 you can; REQ: Cpy (space) DID number to be copied, TYPE: 3902, you simply enter your Unique TN and Your Unique DN for a copy.
Then do and easy change for your DES and any other changes to the copy phone.

Open you book LD 11

Good Luck,

LACITY_Tech
 
Hi Hvehari

To create a new set, all that you need to do is:

Check the available voice units you have in your pbx (ld 20)
choose one, then you must print de unused dn`s, and choose one again, and whith this information you are ready to create a new ext. You can do that en ld 11 for digital sets or ld 10 for analoge sets, or ld 20 for the recent releases. The way in which you can do this, is just some like this..

REQ: new
TYPE: 2008
TN 30 12
DES ti
CUST 0
FDN
TGAR
LDN
NCOS 3
RNPG 84
SSU
SCPW
SGRP
SFLT no
CAC
CLS tld aha dpua pua cnda dnda
HUNT
SCI
PLEV
AST
IAPG
MLWU_LANG
DNDR
KEY 0 mcr 5533
MARP
CPND new
CPND_LANG
NAME prueba ti
XPLN 24
DISPLAY_FMT
VMB
KEY 1 mcr 5533
MARP
CPND
VMB
KEY 2 trn
KEY 3 ao6
KEY 4 cfw 4
KEY 5 rnp
KEY 6 rga
KEY

MEM AVAIL: (U/P): 294920 USED: 311287 TOT: 606207
DISK RECS AVAIL: 388
TNS AVAIL: 597 USED: 403 TOT: 1000
ACD AGENTS AVAIL: 985 USED: 15 TOT: 1000
AST SET AVAIL: 300 USED: 0 TOT: 300

REQ:


Some like this..., anyway check the ld 11/10

Good luck!

 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top