DID

[wwwedward]

I have forgotten how to programe lines from pri service to extensions. I see lines enumarted 123... and so on in the lines options.. I think I am close we capture last three digits.. of did number.

Thanks

 

[mroberts]

How to Install a PRI:

The DTI card should go into Slot 4 first. If you have a second card it would go into Slot 3. One PRI code covers both cards.

To enter the software key code:
From Terminals & Sets – Next until get to
Software keys – Show
Sys ID – Next
Password Keys – Show
Key 1: (enter 1st key code)
Key 2: (enter 2nd key code)
Key 3: (enter 3rd key code)

You must disable the card first, program the card for PRI, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets – Next until you get to
Maintenance – Show
Next until get to Module Status – Show
Show module – Next
KSU (1): Next or State if using (2) cards
KSU (2): State
( ) Ports Busy – Press Disable or Enable
Disable at Once? – Yes

Protocols & Signaling
Hardware – Show
Show Module – Next
Cards on KSU – Show
Cd1 – KSU: Change to PRI – Show
Card Type PRI – Next
Lines: 001-023 – Next
Protocol: SL1 – Next (check with your Telco Carrier for setting)
Type Slave – Next
Bchanseq: Ascend or Descend – Next (check with your Telco Carrier for setting)
CO Fail: TIA–547A – Next
IF Levels: ISDN – Next
Framing: ESF – Next (usually ESF, check with your Carrier
Internal CSU: ON – Next

{need to have either an external CSU or turn the internal one on. If customer needs to use some channels for data then they’ll need a CSU/DSU to split off channels before the 0X32. OR to split off data channels after 0X32 they’ll need a Nortel Data Interface (NDI) plus bandwidth allocation key codes}

DSX1 Bld: 000-100 -Next
Line Coding: B8ZS (usually B8ZS, check with the Carrier)
ClockSrc: Primary (second card would be secondary)

Users cannot access PRI lines directly through line appearances or line pools (except PRI line pools). All outgoing PRI calls are dialed via intercom using routing codes.
When a trunk card is changed to PRI, all existing line appearances for that card are automatically removed.

To Build a Route
Services – Show
Ringing Service – Next to
Routing Service – Show
Routes – Show
Show Route: 001 – Show
Dialout: No Numbr – Leave alone – Next
Use: ( ) – Change to PRI
DN Type: Public

To Build Destination Codes:
Routing Service – Show
Routes – Next
Dest Codes – Show
Show destcode: (enter code) - Next
DstCode: (enter code) – Show
Normal: 000 – Change to route built – Show
AbsorbLength: ALL
Don’t usually have to worry about Night schedule etc.

Line Set Up
Assign each channel (001-023) as trunk type PRI, Line Type: PRI –A.

Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line numbering differs depending on your software)
1.0 sw – Lines number 121-312
R1T1 – Lines number 121-248
1.1 – Lines number 121-248 or 312 XC sw
2.0 to 5.0 – Lines 145-272 or 336XC sw
6.0 – Lines number 157-284 or 348 XC sw
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter digits Telco is sending) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list

Then assign the target line to the appropriate phone.


MRoberts

http://www.a1teletronics.com