Dial with authorization code

[cevamisto]

Hello!

I'am newbie in Ericsson MD110 (BP11/SP13) and i don't know how
to restrict the extension to do a call.I have 2 ISDN trunk (TLU76/1) and 8 analog trunk. I want to restrict the ISDN trunk (no dial from extension) and from analog trunks i want to dial with authorization code.
Somebody could tell me the procedure step by step, even the TRAF,SERV,CDIV for extension ?

Thanks a lot.

 

[rfpui]

first
send prinout of NADAP

 

[cevamisto]

<nadap;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 200 - 215
300 - 315
701 - 706
771 - 773
799
EXTERNAL DESTINATION CODE 0
112
81 - 85
87
9
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
0 0
112 0
2 0
3 0
7 0
8 0
9 0

 

[rfpui]

112 is (I thing) Emergency number
And to make external call are you use 0 or 9 (or both)?
And 8 it is digit to start other external call. What this digit make.

 

[cevamisto]

112 is a emergency number, 0 and 9 is the 2 isdn trunks and 81-85 is the analog trunks. I want to make a call with authorization code on analog trunks not ISDN trunks.

 

[ETBOY]

Hi,

SEND RODDPEST=ALL;

 

[rfpui]

Ok
Now I try to help you.
1.
EXCCP:CAT=ALL;
Look and find not used category. All parameters should be with 00000000….
For example cat 10
Set this category for use with authorization code
EXCCS :CAT=10,TRAF=xx0101yy ,SERV= ,CDIV=…;
Xx and yy copy from other category and SERV and CDIV, too.

If you use generic extension you must set new common service profile
GESPP :CSP=ALL;
Initiate new CSP, for this example new CSP is 10
GESPI :CSP=10,TRAF=xxxx0101yy, SERV=, CDIV=, ROC=, NPRES= ;

2
Initiate authorization code
AUCOI :AUTH=9999,CILCOD=…,CAT=10,CSP=10;
Or if you don’t have CSP
AUCOI :AUTH=9999,CILCOD=….,CAT=10;
3
Now check existing extension category
EXCAPIR=all;
KSCAPIR=all;
Extension which you wont to block for call by press 8 should be have TRAF xx0000yy

4
and now change call discriminator
NACDS :NUM=0&112&2&3&7&9,CDCAT=1;
NACDR :NUM=8;
NACDS :NUM=8,CDCAT=1;

And test ours work
If anybody have other solution or a I make mistake please send commands and correction (s)

 

[rfpui]

Hi Etboy
Why do you want RODDP?

 

[mundus]

Hi' if you wont to force the extension to use account code, then you have to use the LCR (least cost routing) feature, in the tabel DNT1 or/and DNT2 you have the possibility to set the parameter states (by ACCT) if account code dialling shall be required or not, and for the extension you can set the account code category (by ROC).

 

[cevamisto]

Thanks a lot for reply, I'll try.