Hello everyone!
Excuse my English, I have a problem with a 200-24 extreme, if I link a pc okay, I assigned the IP address to dhcp, if I connect a Voip phone but I do not assign address why?
DHCP assigns a patton cascade. (192.168.1.1)
I am attaching my Extreme setup.
#
# Summit200-24 Configuration generated Thu May 13 09:35:26 2010
# Software Version 7.3e.2.4 [non-ssh] by Release_Master on 02/24/05 19:20:09
# Configuration Mode
create vlan "Erixx"
create vlan "Mx-One"
create vlan "voice"
#
# Config information for VLAN Default.
configure vlan "Default" tag 1 # VLAN-ID=0x1 Global Tag 1
configure stpd s0 add vlan "Default"
#
# Config information for VLAN Erixx.
configure vlan "Erixx" tag 10 # VLAN-ID=0xa Global Tag 3
configure vlan "Erixxl" ipaddress 192.168.1.110 255.255.255.0
enable loopback-mode vlan "Erixx"
configure vlan "Erixx" add port 1 untagged
configure vlan "Erixx" add port 2 untagged
configure vlan "Erixx" add port 3 untagged
configure vlan "Erixx" add port 4 untagged
configure vlan "Erixx" add port 5 untagged
configure vlan "Erixx" add port 6 untagged
configure vlan "Erixx" add port 7 untagged
configure vlan "Erixx" add port 8 untagged
configure vlan "Erixx" add port 9 untagged
configure vlan "Erixx" add port 10 untagged
configure vlan "Erixx" add port 11 untagged
configure vlan "Erixx" add port 12 untagged
configure vlan "Erixx" add port 13 untagged
configure vlan "Erixx" add port 14 untagged
configure vlan "Erixx" add port 15 untagged
configure vlan "Erixx" add port 16 untagged
configure vlan "Erixx" add port 17 untagged
configure vlan "Erixx" add port 18 untagged
configure vlan "Erixx" add port 19 untagged
configure vlan "Erixx" add port 20 untagged
configure vlan "Erixx" add port 21 untagged
configure vlan "Erixx" add port 22 untagged
configure vlan "Erixx" add port 23 untagged
configure vlan "Erixx" add port 24 untagged
configure vlan "Erixx" add port 25 untagged
# Config information for VLAN Mx-One.
configure vlan "Mx-One" tag 11 # VLAN-ID=0xb Global Tag 4
configure vlan "Mx-One" qosprofile "QP8"
configure vlan "Mx-One" ipaddress 192.168.2.1 255.255.255.0
#
# Config information for VLAN voice.
#
# Banner Configuration
#
configure banner
*****************************************************
* Erixx s.r.l. *
* Distribution Switch Laboratory *
*****************************************************
* Accesso consentito ai soli utenti autorizzati *
*****************************************************
enable web http
disable web https
# SNMP Configuration
configure snmp sysName "Erixx"
configure snmp sysLocation "Erixx"
enable cli-prompt-number
# Load Sharing Configuration
# Ports Configuration
configure port 25 preferred-medium fiber
configure port 26 preferred-medium fiber
# Spanning tree information
# MAC FDB configuration and static entries
configure ipfdb agingtime 0
# -- IP Interface[0] = "Default"
# -- IP Interface[1] = "Erixx"
enable ipforwarding vlan "Erixx"
disable icmp timestamp vlan "Erixx"
disable icmp address-mask vlan "Erixx"
# -- IP Interface[2] = "Mx-One"
# Global IP settings.
disable icmp access-list
enable bootprelay
configure bootprelay add 192.168.1.1
#
# IP ARP Configuration
# Multicast configuration
disable igmp snooping
enable igmp snooping vlan "Default"
enable igmp snooping vlan "MacVlanDiscover"
enable igmp snooping vlan "Erixx"
enable igmp snooping vlan "Mx-One"
enable igmp snooping vlan "voice"
# RIP interface configuration
# RIP global parameter configuration
#
# PIM Router Configuration
#
#
# Static MRoute Configuration
# Ospf Area Configuration
# Ospf Range Configuration
# Interface Configuration
# Virtual Link Configuration
# Ospf ASE Summary Configuration
# OSPF Router Configuration
# ESRP Interface Configuration
#ELRP Configuration
# VRRP Configuration
# EAPS configuration
# EAPS shared port configuration
# NAT configuration
configure nat timeout 300
# SNTP client configuration
#
# Radius configuration
#
# TACACS configuration
disable tacacs
disable tacacs-authorization
disable tacacs-accounting
# Mac Vlan Configurations
#
# Access-mask Configuration
#
# Access-list Configuration
#
# Rate-limit Configuration
#
# System Dump Configuration
#
## SNMPV3 EngineID Configuration
#
## SNMPV3 USM Users Configuration
#
#
# SNMPV3 MIB Views Configuration
#
#
# SNMPV3 VACM Access Configuration
#
#
# SNMPV3 USM Groups Configuration
#
#
# SNMPV3 Community Table Configuration
#
#
# SNMPV3 Target Addr Configuration
#
#
# SNMPV3 Target Params Configuration
#
#
# SNMPV3 Notify Configuration
#
#
# SNMPV3 Notify Filter Profile Configuration
#
#
# SNMPV3 Notify Filter Configuration
#
# System-wide Debug Configuration
#No System-wide debug tracing configured
#Vlan Based Debug Configuration
#
#No Vlan-based debug-tracing configured
#Port Based Debug Configuration
#
#No Port based debug-tracing configured
# IP subnet lookup configuration
# Network Login Configuration
configure vlan Erixx dhcp-address-range 192.168.1.10 - 192.168.1.99
configure vlan Erixx dhcp-options default-gateway 192.168.1.1
configure vlan Erixx dhcp-options dns-server 80.93.143.42
enable dhcp port 11 vlan Erixx
enable dhcp port 12 vlan Erixx
enable dhcp port 13 vlan Erixx
enable dhcp port 14 vlan Erixx
enable dhcp port 15 vlan Erixx
enable dhcp port 16 vlan Erixx
enable dhcp port 17 vlan Erixx
enable dhcp port 18 vlan Erixx
enable dhcp port 19 vlan Erixx
enable dhcp port 20 vlan Erixx
enable dhcp port 21 vlan Erixx
enable dhcp port 22 vlan Erixx
enable dhcp port 23 vlan Erixx
enable dhcp port 24 vlan Erixx
enable dhcp port 25 vlan Erixx
# Event Management System Configuration
# Event Management System Log Filter Configuration
# Event Management System Log Target Configuration
# Enhanced-dos-protect configuration
disable enhanced-dos-protect ipfdb
disable enhanced-dos-protect rate-limit
#
# End of configuration file for "Erixx".
Excuse my English, I have a problem with a 200-24 extreme, if I link a pc okay, I assigned the IP address to dhcp, if I connect a Voip phone but I do not assign address why?
DHCP assigns a patton cascade. (192.168.1.1)
I am attaching my Extreme setup.
#
# Summit200-24 Configuration generated Thu May 13 09:35:26 2010
# Software Version 7.3e.2.4 [non-ssh] by Release_Master on 02/24/05 19:20:09
# Configuration Mode
create vlan "Erixx"
create vlan "Mx-One"
create vlan "voice"
#
# Config information for VLAN Default.
configure vlan "Default" tag 1 # VLAN-ID=0x1 Global Tag 1
configure stpd s0 add vlan "Default"
#
# Config information for VLAN Erixx.
configure vlan "Erixx" tag 10 # VLAN-ID=0xa Global Tag 3
configure vlan "Erixxl" ipaddress 192.168.1.110 255.255.255.0
enable loopback-mode vlan "Erixx"
configure vlan "Erixx" add port 1 untagged
configure vlan "Erixx" add port 2 untagged
configure vlan "Erixx" add port 3 untagged
configure vlan "Erixx" add port 4 untagged
configure vlan "Erixx" add port 5 untagged
configure vlan "Erixx" add port 6 untagged
configure vlan "Erixx" add port 7 untagged
configure vlan "Erixx" add port 8 untagged
configure vlan "Erixx" add port 9 untagged
configure vlan "Erixx" add port 10 untagged
configure vlan "Erixx" add port 11 untagged
configure vlan "Erixx" add port 12 untagged
configure vlan "Erixx" add port 13 untagged
configure vlan "Erixx" add port 14 untagged
configure vlan "Erixx" add port 15 untagged
configure vlan "Erixx" add port 16 untagged
configure vlan "Erixx" add port 17 untagged
configure vlan "Erixx" add port 18 untagged
configure vlan "Erixx" add port 19 untagged
configure vlan "Erixx" add port 20 untagged
configure vlan "Erixx" add port 21 untagged
configure vlan "Erixx" add port 22 untagged
configure vlan "Erixx" add port 23 untagged
configure vlan "Erixx" add port 24 untagged
configure vlan "Erixx" add port 25 untagged
# Config information for VLAN Mx-One.
configure vlan "Mx-One" tag 11 # VLAN-ID=0xb Global Tag 4
configure vlan "Mx-One" qosprofile "QP8"
configure vlan "Mx-One" ipaddress 192.168.2.1 255.255.255.0
#
# Config information for VLAN voice.
#
# Banner Configuration
#
configure banner
*****************************************************
* Erixx s.r.l. *
* Distribution Switch Laboratory *
*****************************************************
* Accesso consentito ai soli utenti autorizzati *
*****************************************************
enable web http
disable web https
# SNMP Configuration
configure snmp sysName "Erixx"
configure snmp sysLocation "Erixx"
enable cli-prompt-number
# Load Sharing Configuration
# Ports Configuration
configure port 25 preferred-medium fiber
configure port 26 preferred-medium fiber
# Spanning tree information
# MAC FDB configuration and static entries
configure ipfdb agingtime 0
# -- IP Interface[0] = "Default"
# -- IP Interface[1] = "Erixx"
enable ipforwarding vlan "Erixx"
disable icmp timestamp vlan "Erixx"
disable icmp address-mask vlan "Erixx"
# -- IP Interface[2] = "Mx-One"
# Global IP settings.
disable icmp access-list
enable bootprelay
configure bootprelay add 192.168.1.1
#
# IP ARP Configuration
# Multicast configuration
disable igmp snooping
enable igmp snooping vlan "Default"
enable igmp snooping vlan "MacVlanDiscover"
enable igmp snooping vlan "Erixx"
enable igmp snooping vlan "Mx-One"
enable igmp snooping vlan "voice"
# RIP interface configuration
# RIP global parameter configuration
#
# PIM Router Configuration
#
#
# Static MRoute Configuration
# Ospf Area Configuration
# Ospf Range Configuration
# Interface Configuration
# Virtual Link Configuration
# Ospf ASE Summary Configuration
# OSPF Router Configuration
# ESRP Interface Configuration
#ELRP Configuration
# VRRP Configuration
# EAPS configuration
# EAPS shared port configuration
# NAT configuration
configure nat timeout 300
# SNTP client configuration
#
# Radius configuration
#
# TACACS configuration
disable tacacs
disable tacacs-authorization
disable tacacs-accounting
# Mac Vlan Configurations
#
# Access-mask Configuration
#
# Access-list Configuration
#
# Rate-limit Configuration
#
# System Dump Configuration
#
## SNMPV3 EngineID Configuration
#
## SNMPV3 USM Users Configuration
#
#
# SNMPV3 MIB Views Configuration
#
#
# SNMPV3 VACM Access Configuration
#
#
# SNMPV3 USM Groups Configuration
#
#
# SNMPV3 Community Table Configuration
#
#
# SNMPV3 Target Addr Configuration
#
#
# SNMPV3 Target Params Configuration
#
#
# SNMPV3 Notify Configuration
#
#
# SNMPV3 Notify Filter Profile Configuration
#
#
# SNMPV3 Notify Filter Configuration
#
# System-wide Debug Configuration
#No System-wide debug tracing configured
#Vlan Based Debug Configuration
#
#No Vlan-based debug-tracing configured
#Port Based Debug Configuration
#
#No Port based debug-tracing configured
# IP subnet lookup configuration
# Network Login Configuration
configure vlan Erixx dhcp-address-range 192.168.1.10 - 192.168.1.99
configure vlan Erixx dhcp-options default-gateway 192.168.1.1
configure vlan Erixx dhcp-options dns-server 80.93.143.42
enable dhcp port 11 vlan Erixx
enable dhcp port 12 vlan Erixx
enable dhcp port 13 vlan Erixx
enable dhcp port 14 vlan Erixx
enable dhcp port 15 vlan Erixx
enable dhcp port 16 vlan Erixx
enable dhcp port 17 vlan Erixx
enable dhcp port 18 vlan Erixx
enable dhcp port 19 vlan Erixx
enable dhcp port 20 vlan Erixx
enable dhcp port 21 vlan Erixx
enable dhcp port 22 vlan Erixx
enable dhcp port 23 vlan Erixx
enable dhcp port 24 vlan Erixx
enable dhcp port 25 vlan Erixx
# Event Management System Configuration
# Event Management System Log Filter Configuration
# Event Management System Log Target Configuration
# Enhanced-dos-protect configuration
disable enhanced-dos-protect ipfdb
disable enhanced-dos-protect rate-limit
#
# End of configuration file for "Erixx".