Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

DFTX

Status
Not open for further replies.

Ronj123434

IS-IT--Management
Oct 25, 2021
6
US
Does anyone have a cheat sheet of what some of these error messages are? For example is there anywhere I can get information for the following.

LP10-0-ACT
LP02-0-ACT
LP12-0-ACT
LP04-0-ACT
LP08-0-ACT

These don't seem to be a huge problem because it shows up in DFTX, but it's not a major or minor. I just always see the same errors everytime I do a read messages and it would be nice to know what exactly they mean.
 
Post a sample of one of the full messages.



There are 10 kinds of people in the World.

Those that understand Binary and those that don't.
 
Examples.

LP12-0-ACT
1:50 F7 00 00 00 00 00 00 2:00 00 00 00 00 00 00 00 3:00 00 00 00 00 00 00 00 4:00 00 00 00 00 00 00 00
5:00 00 00 00 00 00 00 00 6:00 00 00 00 00 00 00 00 7:00 00 00 00 00 00 00 00 8:00 00 00 00 00 00 00 00
KIND of CYCLIC DIAGNOSIS: No Trunk Ineffective Hold
MG-0 UNIT-0: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-1: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-2: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-3: -
MG-1 UNIT-0: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-1: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-2: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-3: Trunk Ineffective Hold is Not Detected

LP04-0-ACT
1:50 FF 00 00 00 00 00 00 2:00 00 00 00 00 00 00 00 3:00 00 00 00 00 00 00 00 4:00 00 00 00 00 00 00 00
5:00 00 00 00 00 00 00 00 6:00 00 00 00 00 00 00 00 7:00 00 00 00 00 00 00 00 8:00 00 00 00 00 00 00 00
KIND of CYCLIC DIAGNOSIS: No Trunk Ineffective Hold
MG-0 UNIT-0: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-1: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-2: Trunk Ineffective Hold is Not Detected
MG-0 UNIT-3: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-0: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-1: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-2: Trunk Ineffective Hold is Not Detected
MG-1 UNIT-3: Trunk Ineffective Hold is Not Detected

 
LP is Local Partition
XX is the lowest module group in that IMG.

LP12 = the 13th IMG (stack)
LP04 = the 5th IMG (stack)

So you must be a Fusion system or UMG.

The system is told to check for this condition while doing routine diagnostics.

In ASYD Sys 1 Index 89
b4 - Trunk Ineffective Hold Check Note 4, Note 5, Note 6
0/1 = No/Yes
b5 - Trunk Ineffective Hold Detection Note 4, Note 5, Note 6
0/1 = No/Yes

Note 4: When Trunk Ineffective Hold Check or Trunk Ineffective Hold Detection is executed
while bit 0 of ASYDL SYS1 Index 1034 is set to 1, Virtual Register Ineffective Check
is also enabled.

Note 5: There is a limit on the number of CCIS trunks per LP for this diagnostic process to
work. The maximum number of CCIS trunks for each LP is 150 (A maximum of 150
ports can be configured as CCIS trunks).
For an LP where more than 150 CCIS trunks are registered, system message [7-P]
([52H] “Trunk Ineffective Hold Detected Impossible”) is generated, and the diagnostic
task is not executed (For other LPs where no such error is detected, the task is
conducted as scheduled).

Note 6: The setting of CCIS Control System Interoffice Audit Test (ASYD, SYS1, Index 188,
Bit 0: 0/1= Required/Not Required) is valid only when activating TRK Ineffective Hold
Check function of the periodic test, and releases the Ineffective Hold Trunk of self/
destination node.
If there is peer to peer by “CCIS over IP with PHC” service in self office, assign this
system data to “1= Not required”, only Ineffective Hold Trunk is released (Regarding
opposite trunk, depending on whether Ineffective Hold Check is checked or not in
the opposite node).

What it does when it detects the condition is defined in

ASYD Sys 1 Index 86
bit3, bit2
00 = The trunks being held at present are forcibly released, except the trunks being held on two-way calls (station-to-station call, station-to trunk, external trunk-to-external trunk call).
10 = All trunks being held at the present are forcibly released
01 = LENS of the trunk detected display as system message

Data is in the OpsMaint_v9.pdf manual.




There are 10 kinds of people in the World.

Those that understand Binary and those that don't.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top