deletion

[jaylek]

Dear all,

System is ERICSSON
VERSION=CXP1010101/4/TSWSP05/R6A
2 LIM SYSTEM where two PRI cards are in LIM1.

I need some help to resolve this issue.

I was having a DID block from 245000000 to 24500999
Outgoing and incoming was working fine. Only for incoming I have programmed NUTRI and that was like this format. example with extension 759.
NUTRI:ENTRY=24500759,CNVTYP=0,NUMTYP=4,PRE=759.

Now we are moving with 4digit number. Plans to add " 1 " before old extension. (245001759).
At present it shows 245001759. but we need to remove 1 from that number because the public exchange will send only 24500759.

Internal is ok 1759
External should show only 24500759.

Can anyone help to resole this?

Thanks in advance.

 

[whosrdaddy]

you only need one entry (if you map extensions to the DID nr)

NUTRI:ENTRY=24500,CNVTYP=0,NUMTYP=4,PRE=1;

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[jaylek]

Dear Whosrdaddy,

I am not in site and we are off today,but try to check today. I request you a small clarification.
The command you mentioned here is for outgoing?
because i saw CNVTYP = 0
NUTRI:ENTRY=24500,CNVTYP=0,NUMTYP=4,PRE=1;

My issue was to delete 1 when I dial an external number.
For example from extension 1160 if i dial a mobile number the number shows in mobile as 245001160. If the mobile user tries to call back 245001160 it will not reach because our DID number is 24500160.

My question was in this scenario if i dial from extension 1160 to a mobile it shoud show 24500160. 1 should be deleted.

Can you please look into this?

Thanks again.

 

[phrankie]

Try this:

NUTRI:ENTRY=1,CNVTYP=1,NUMTYP=4,PRE=24500,TRC=1;

Thanks.

 

[whosrdaddy]

the command I mentioned is for incoming calls.

if you want to change outgoing CLI make sure you must enabled CLI on the extension (appriopriate SERV digit on analog/digital/generic)

and then do this:

NUTRI:ENTRY=1,CNVTYP=1,NUMTYP=10,PRE=24500,TRC=1;

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[jaylek]

Dear all,

Thanks and I will update you tomorrow after checking this.

 

[jaylek]

Dear Whosrdaddy,

It is not working.

NUTRI:ENTRY=1,CNVTYP=1,NUMTYP=10,PRE=24500,TRC=1; When I initiate this the number shows 24500000. I hope you understood my requirement.

In my extension 1160 if I dial out the number shows 245001160. I dont need this number to be displayed. I need 24500160 (1 has been removed).

Also I am attaching the route and extension parameters.

<rocap:ROU=10;ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
10 7130000000000010 5 0100000001 0 30 128 00151514 211100010031 111111

<KSCAPIR=1160;KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE TRM ADC LANG BSEC
1160 00010115 0215120700 000120000 000001 26 0 00000000010000 F 0

<NUTRP:CNVTYP=1;NUMTYP=10,PRE=24500,TARDST=9;NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
1 1 10 24500 1 0

Please help.

 

[jaylek]

HAI FRIENDS,

I managed to sort out the problem with the inputs received.
Still on job. Update later.

Thanks a lot for the help.

 

[zonezone219]

how conect Mx one to Bp250?
Hi all
now my company have 2 node. node 1 use system Mx-One and node 2 use BP250.now my boss told me do connect 2 node together. I can do on system Bp250.On system Mx-One i'm notyet do so i hope anybody in here advance to me do it.
i hope receive somebody guide me do it.Thanks all member read theread this.thanks and best regard