Delete a board ?

[Astonces]

Sorry by my english.

I can´t delete a board position that CNHUI update, and I think that is bad update.

<CNHUI:BPOS=1-1-60;
ORDERED

AUTHORITY CLASS 7
(C) COPYRIGHT ERICSSON
ERICTEL 30JAN03 17:14:08 1-0-60-04 TELNET3

<CNHUI:BPOS=1-1-60;
ORDERED
<CNLIPEV=YES;

LIM CONFIGURATION
LIM NUMBER 1
LIM CONTROL LIM CONTROL NUMBER OF SERVICE
SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM
A EXECUTING 0 ACTIVE
B NOT EQUIPPED
MEMORY MEMORY MEMORY SPARE
VOLUME SPARE AFTER PACKING
65535 KB 25376 KB 25376 KB
BUAR1 3586 KB BUAR2 2793 KB

DEVICE BOARDS
NUMBER OF
BPOS BOARDID INDIVIDUALS SERVICE STATE
001-0-00 57 32 ACTIVE
001-0-10 102 32 ACTIVE
001-0-20 77 16 ACTIVE
001-0-22 NOT EQUIPPED
001-0-23 NOT EQUIPPED
001-0-30 NOT EQUIPPED
001-0-31 NOT EQUIPPED
001-0-32 NOT EQUIPPED
001-0-33 NOT EQUIPPED
001-0-40 2 8 ACTIVE
001-0-41 NOT EQUIPPED
001-0-42 2 8 ACTIVE
001-0-43 NOT EQUIPPED
001-0-50 NOT EQUIPPED
001-0-51 NOT EQUIPPED
001-0-52 NOT EQUIPPED
001-0-53 NOT EQUIPPED
001-0-60 106 16 ACTIVE
001-0-62 NOT EQUIPPED
001-0-63 NOT EQUIPPED
001-0-70 NOT EQUIPPED
001-0-71 NOT EQUIPPED
001-0-72 NOT EQUIPPED
001-0-73 42 4 ACTIVE
001-1-00 57 32 ACTIVE
001-1-10 102 32 ACTIVE
001-1-20 77 16 ACTIVE
001-1-22 2 8 ACTIVE
001-1-23 NOT EQUIPPED
001-1-30 2 8 ACTIVE
001-1-31 NOT EQUIPPED
001-1-32 NOT EQUIPPED
001-1-33 NOT EQUIPPED
001-1-40 108 16 ACTIVE
001-1-42 NOT EQUIPPED
001-1-43 NOT EQUIPPED
001-1-50 70 8 ACTIVE
001-1-51 NOT EQUIPPED
001-1-52 NOT EQUIPPED
001-1-53 NOT EQUIPPED
001-1-60 254 2 SYSTEM BLOCKED <---THIS BOARD
001-1-61 NOT EQUIPPED
001-1-62 NOT EQUIPPED
001-1-63 NOT EQUIPPED
001-1-70 NOT EQUIPPED
001-1-71 NOT EQUIPPED
001-1-72 NOT EQUIPPED
001-1-73 NOT EQUIPPED


END
<CNBOI:BPOS=1-1-60,NUMIND=2,BRDID=113;
CNBOI:BPOS=1-1-60,NUMIND=2,BRDID=113;
SURE? (YES/NO)
<Y;
NOT ACCEPTED
POSITION ALREADY OCCUPIED

SPONTANEOUS PRINTOUT

CONFIGURATION HARDWARE UPDATE
BPOS=001-1-60
POSITION ALREADY ASSIGNED
END
<CNBOE:BPOS=1-1-60;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-1-60-01

END

SPONTANEOUS PRINTOUT

CONFIGURATION HARDWARE UPDATE EXECUTED
<CNBOE:BPOS=1-1-60;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-1-60-01

END
<CNBOE:BPOS=1-1-60;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-1-60-01

END
<SYEDP:BPOS=1-1-60;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
001-1-60-00 254 IPL
001-1-60-01 254 IPL
END


THANK YOU,,

 

[Avstral]

The easiest way to remove this problem is LADAI;

&quot;The exchange data will be restored to the status as it had at the last system dump occasion&quot;.


But why did you try to do CNBOI before CNHUI command finished (after CNHUI you must wait for the message &quot;SPONTANEOUS PRINTOUT ...CONFIGURATION HARDWARE UPDATE&quot.

Why did try to do CNBOI on already occupied position?

I can't insist, but it looks like you confused system trying to speed up the process.

Best regards

 

[patcher]

Try LADAI according to Avstral. In my opinion Astonces in doing CNBOI just to show you that the position is occupied. This will not do any harm for sure. If LADAI does not work, tell me and we will fix it. //patcher

 

[Astonces]

Hi, patcher

LADAI does not work, what can I do with this board?

Can I delete board with SACOS or any command?

My release is BC11 SP9,

Thanks you.

 

[lalrl]

brdid=113 means old ELU32 with 2 gateways. This card should not be used anymore. Ericsson offers against new ELU32 to change this card for 100 Euro.

A very sure solution for your problem would be a lalrl (complet reload). But this only helps, if you have not manually or automatically dumped. Check with dubdp. Note! PABX will be completely down for a while... And you will have the old data in your pabx from the last dump. And some manual procedures (i.e calldiversions) are inactiv and so on) How many LIM do you have?

 

[lalrl]

... on the other hand: if ladai does not work, then I´m afraid system has made a dump after your action. In this case: lalrl has no sense...

 

[FICRI]

According to the print CNBOE does not work because INDIVIDUAL STILL INITIATED ON EQU 1-1-60-01.

SYEDP shows:
EQU BOARDID TYPE DIR ROU/TRU
001-1-60-00 254 IPL
001-1-60-01 254 IPL

IPL=IP-Extension so try IPBOE:BPOS=1-1-60;

IPBOE = IP board network configuration end

 

[patcher]

FICRI is right. The board is assigned and with IP address in it. IPBOE will fix your problem. //patcher

 

[Astonces]

Hi,

When I do IPBOE:
<IPBOE:BPOS=1-1-60;
IPBOE:BPOS=1-1-60;
SURE? (YES/NO)
<Y;
NOT ACCEPTED

INCORRECT BOARDTYPE
<

Which are the steps for do this right?

Thank you...

 

[FICRI]

Do you know which boardtype you have in 1-1-60?
BOARDID=254 is strange because maximum value for BOARDID is 127.

 

[Astonces]

Yes Ficri,

I think the same.

Somebody know if I can use any SACOS for delete this board?

And how can I do?

Thanks

 

[m110d]

BRDID=254 shows when the firmware is bad or corrupted on the board. Try loading the firmware for this BPOS so that it shows correct on CNLIP, ie BRDID=113.
If you have the firmware file the procedure is not too complicated. The option of using SACOS to get around this problem might be more trouble than it is worth if things went wrong.

 

[patcher]

Did you ever try to use IPBOP:BPOS=ALL; ???? Okay, do this command:
SACOP:LIM=1,UNIT=DCP,FILNO=3,RELOFF=0&&6,POINT=1C0&1C1;
Post the info of IPBOP&SACOP here. //patcher

 

[Astonces]

Hi Patcher,

<IPBOP:BPOS=ALL;
IP NETWORK INTERFACE DATA
BPOS IP ADDRESS MASK ROUTER
1-1-60 192.168.0.45 255.255.255.0 -

END

<SACOP:LIM=1,UNIT=DCP,FILNO=3,RELOFF=0&&6,POINT=1C0&1C1;
MEMORY CONTENT ON INDIVIDUAL POSITION
EXE A
FILE NUMBER RELOAD FILE START DS FILE START
3 0000074A
POINT RELOFF DSOFF ADDRESS DATA ISO
01C0 0000 0000368A 00 .
01C0 0001 0000368B 00 .
01C0 0002 0000368C 01 .
01C0 0003 0000368D B1 .
01C0 0004 0000368E 38 8
01C0 0005 0000368F 02 .
01C0 0006 00003690 02 .
01C1 0000 000036A5 00 .
01C1 0001 000036A6 00 .
01C1 0002 000036A7 01 .
01C1 0003 000036A8 B1 .
01C1 0004 000036A9 38 8
01C1 0005 000036AA 02 .
01C1 0006 000036AB 02 .
END


Thanks,