Cyclic hunting for incoming trunk

[Monrovia]

Hi all,

I am facing a problem in my system that, sometimes my trunks get hang up (status = busy, Trafic = Idle) so from my other regional offices can not call to my office.

It is ISDN trunk (E1 - 30b+d). I believe, it is first some lines in that route is creating this issue. so, how can i make the route in cyclic for incoming, thus to overcome this problem?

FOR OUTGOING CALL, IT IS D3 IN SEL FOR SEQUENTIAL SELECTION.
[TT]<ROCAP:ROU=166;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
166 7110000000000010 5 3110000000 0 30 128 00151515 511110020031 111111 [/TT]

but for cyclic what & where to change the parameter?

 

[Monrovia]

Oops, one small correction

[tt]<ROCAP:ROU=166;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
166 0110000000000010 5 3110000000 0 30 128 00151515 511110020131 111111 [/tt]

D1 in SEL is 0. not 7.

will that make some changes, i mean for my problem? Will D1 7 will solve my problem?

 

[Monrovia]

Why there is no Edit option in this forum

there is one more question,

how to make it cyclic for outgoing as well, selection of another trunk in the same route

 

[whosrdaddy]

please post RODAP:ROU=166;

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Monrovia]

[tt]<RODAP:ROU=166;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
166 SL60 H'00000310 H'15420000 H'06300000 NO [/tt]

 

[whosrdaddy]

more questions:

your PBX: version? (CADAP
other PBX: type/version?

/Daddy



-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Monrovia]

[tt]
<CADAP;
CALENDAR DATA
IDENTITY=MD110
VERSION=CXP1010101/2/BC12SP7/R4A [/tt]

it is BC12 sp7

 

[whosrdaddy]

what for type are the remote pbx systems?

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Monrovia]

all the offices has the same system. MD110 BC12 sp7

once again, here it is all the details

my system& trunk details:

OFFICE 1:
[TT]<CADAP;
CALENDAR DATA
IDENTITY=MD110
VERSION=CXP1010101/2/BC12SP7/R4A
10:27:30
MON 10 NOV 2008
END

<ROCAP:ROU=166;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
166 7110000000000010 5 3110000000 0 30 128 00151515 511110020031 111111

END

<RODAP:ROU=166;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
166 SL60 H'00000310 H'15420000 H'06300000 NO [/TT]

OFFICE 2:
[TT]<ROCAP:ROU=166;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
166 7110000000000010 7 3110000000 0 30 128 00151515 111110120031 001100

<RODAP:ROU=166;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
166 SL60 H'00000310 H'15420000 H'46300000 NO [/TT]

OFFICE 3:
[TT]<ROCAP:ROU=166;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
166 0110000000000010 5 3110000000 0 30 128 00151515 511110020131 111111

<RODAP:ROU=166;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
166 SL60 H'00000310 H'15420000 H'46300000 NO [/TT]

In this, office 3 is the problematic place - which creates the problems as i said above

 

[kank]

Is it peer to peer?

 

[Monrovia]

peer to peer, i dont know about it.

but, all the calls in-between the offices are internal - like extensions.

 

[kank]

Ok try this: Unassign all the trunks in the remote offices (ROEQE:ROU=166,TRU=X-XX). Re-assign them in an order according to your need. For example: You may have TLU76 on 1-0-20. Assign the trunk numbers:
ROEQI:ROU=166,TRU=1-1,EQU=1-0-20-31;
ROEQI:ROU=166,TRU=1-2,EQU=1-0-20-30;
ROEQI:ROU=166,TRU=1-3,EQU=1-0-20-29;
.
.
.
.
ROEQI:ROU=166,TRU=1-30,EQU=1-0-20-01;

Make a dump before start. If you confuse any time LADAI to get back to original.

 

[Monrovia]

OK. I will do that.
Actually we are using only 10channels on this trunk, not all 30 channels - for more bandwidth on each channel.

but, will this make the outgoing trunks as cyclic manner? i mean, each time if i select the route-dest code(here no dest as this is internal calls) it will select different trunks in a cyclic way?

 

[kank]

Also try to change the 3rd parameter of SEL to 4.

 

[fcpli]

Monrovia!
In my opinion you are on a wrong track asking for cyclic...
The problem is with VARO: You should not use the same D3 on both sites. Change the remote to D3=4, this should do the trick. SEL D3 changa won't help.