ctt10

[ozgur74]

Hello,
i have bc10ta and i want to connect ctt10 .
I have connacted tiu5600 , psu and 77 keys touch terminal .

i typed this command (like isinor had sent to forum):

CNBOI:BPOS=1-0-20,BRDID=77,NUMIND=32;
EXCCS:CAT=11,TRAF=01151515,SERV=02001200,CDIV=011150000;
Some of the SERV bits and
DKEXIIR=1400,EQU=1-0-20-03,MON1=1-0-20-04,SPE2=1-0-20-19,MON2=1-0-20-20,CAT=11,SIZE=11,ATTR=11;
DKEDPIR=ALL;
The Functions keys 5 and 6 have special usage – Log on and Password.
DKFKIIR=1400,KEY=6,FCN=NSK,ID=54000,ABN=0;
DKFKIIR=1400,KEY=5,FCN=NSK,ID=1234,ABN=0;
DKFKP;

When i start tiu , i have message "waiting" and after "key control" , but nothing else "dasl1 not ok ,dasl2 not ok ..."
When i call 1400 it's like busy ...


To create 1400 i had used
NANSI:numtyp=...
NADAP;

please help me ...

ozgur

 

[ozgur74]

Now i see waiting on left of screen and on the right i see files revisions: ..

and ctt status ASSIVE

?

 

[Isinor]

Hi Ozgur74,

From Alex
2.2 Waiting
When both the TIU and panel power has been switched on, "WAITING" shall pop up on the 77-key plasma panel and remain displayed until the CTT is activated by the exchange. If "WAITING" does not appear on the screen, do the following until "WAITING" is displayed:

1 Restart the panel (either by power-up or restart command from PC). Wait approximately 10 seconds and then reset the TIU.

2 Still not OK - Control that the panel is set up with the proper software. This is done by reading the revision of the panel application software in the panel installation setup menu (see Software downloading to the CTT10 panels). If no revision is shown, application software has to be reloaded to the panel.

Control that the baud-rate setting between TIU and panel is correct.

3 Still not OK - sort out whether the problem relates to the TIU or the panel (by testing the units towards a panel or TIU respectively that is known to work). Replace the faulty unit.


Also...
The TIU has firmware that can be uploaded from a PC. Have you done this?

Make sure the TIU is set to upload
[tt]
DIP SWITCH S302 4 3 2 1
TA: Normal use OFF OFF OFF OFF
SW uploading from PC OFF OFF OFF ON
[/tt]

You need to get PCPLUS and the TIU files from you TA Documentation which has the floppy disks. Or a new PCPLUS replacement app that I know exists but have never used.

Make sure that you have the line wiring from the MD110 to TIU correct.

EQU=1-0-20-03 = LINES A0 & B0,
MON1=1-0-20-04 = LINES A1 & B1

Good luck...

Regards
Isinor

 

[Isinor]

Hi,

Oops... The DIR and the ID have to match... I think...

DKEXI:DIR=1400,EQU=1-0-20-03,MON1=1-0-20-04,SPE2=1-0-20-19,MON2=1-0-20-20,CAT=11,SIZE=11,ATTR=11;
DKEDPIR=ALL;
The Functions keys 5 and 6 have special usage – Log on and Password.
DKFKIIR=1400,KEY=6,FCN=NSK,ID=1400,ABN=0;

Regards
Isinor

 

[ozgur74]

hello isinor
I have upgrade tiu and now it's ok
but , because there is allways "but"
I can make a call , i have all menus , but no ring and no microfone ans speaker ?
ther is a buzzer on the right but no ring ?

best regards
ozgur

 

[Isinor]

Hi Ozgur74,

You need to program the fcn keys using...

DKFKIIR=54000,KEY=4,FCN=CAB;

This is the list of fcn keys...
Key Function
4 Call Back CAB
5 Password
6 Identity ID
7 Parking PRK
8 Redial RDL
9 Right Handset HED2
10 Right Monitor MON2
11 Left Monitor SPE1
12 Transfer TRF
13 Monitor to Right Handset SPE2
14 Left Handset HED1
15 Monitor to Left Handset MON1
16 Diversion DIV
17 Conference CONF
18 Broadcast Select BCTS
21 Volume Adjustment VOLA
22 Volume Increment VOLI
23 Volume Decrement VOLD
24 Broadcast Activate BCTA
26 Post Dialling digits SUF
29 Free on second line ODN2

Regards
Isinor

 

[ozgur74]

I need to program fcn key to have a ring(all) ?
but i dont see a fcn key for ringing ...

Sorry for my questions but it 's very different from a normal PO ...

 

[Isinor]

Hi Ozgur74,

A both-way direct access key for a CTT10 is initiated using an ADN number with a suitable common category and a B-Number. You can also provide an ID for the key, this is displayed on the screen of the CTT10. The display is 2 rows of 6 chars, use '/' as a space. If the BNUM is used by several CTT10's then it might be best to create a common abb dial and point the BNUM at the Common ABB Dial.

DKDAI:DIR=54000,KEY=41,ADN=54001,CAT=15,BNUM=1001,ID=Group/1,ATTR=10;
DKKDP:DIR=54000;

Incoming callers who provide a number can have an IDENTITY assigned to a maximum of 16 alphanumeric characters.

DKNIS:BNUM=1001,ID=Group 1;
DKNIP:BNUM=ALL;

Regards
Isinor

 

[ozgur74]

MAny thanks , but i think i don't explain my problem corrctly .
So when you take the user manual , you can see description of terminal on page 5 , number 10 is buzzer/loudspeaker ( in front , at the top right on panel ),just near rs232 connector of panel (ctt10).
My problem is this buzzer , i don't have any noise or ringing or anything else on that .

best regards
ozgur

 

[Isinor]

Hi,

Press the ID key twice (Number 7 - Description of terminal on page 5), you can then choose 1=left, 2=right or 3=buzzer

or

Check the TIU to CDU-1 and CDU-3 is correct.

Regards
Isinor

 

[ozgur74]

Yes that is my problem , i have no buzzer.
But for the moment i don't have cdu ?
I just need to make a ring test of my panel .
Can't i ?

thanks a lot isinor

 

[jinjin]

Have you check your UPD files.

 

[ozgur74]

i don't think so,
what is this ?
and i do it ?

 

[ozgur74]

sorry , i want to say : how can i do it ?