cs1000m tieline to audiocodes gateway

[zoomaster]

I am trying to TIE to an audiocodes Mediant 1000 gateway. I am not sure of configuring the D ch. I am not sure about the IFC and SIDE setting on CS1000 and how the gateway should be set to match the CS1000. I have tried sl1 with Side = NET, D100 with SIDE = usr and the gateway was set as usr and NET repectively.
this is my DCH 20

CTYP MSDL
GRP 0
DNUM 15
PORT 1
DES IVR
USR PRI
DCHL 11
OTBF 127
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID **
RCAP ND2 TAT
MBGA NO
OVLR NO
OVLS NO
PRI INTERFACE ID
034 2
T200 3
T203 10
N200 3
N201 260
K 7

and one of the tie lines -

PRI* TRK LOOP 11 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE 3VCE * CH 02 - IDLE TIE 3VCE *
CH 03 - IDLE TIE 3VCE * CH 04 - IDLE TIE 3VCE *
CH 05 - IDLE TIE 3VCE * CH 06 - IDLE TIE 3VCE *
CH 07 - IDLE TIE 3VCE * CH 08 - IDLE TIE 3VCE *
CH 09 - IDLE TIE 3VCE * CH 10 - IDLE TIE 3VCE *
CH 11 - IDLE TIE 3VCE * CH 12 - IDLE TIE 3VCE *
CH 13 - IDLE TIE 3VCE * CH 14 - IDLE TIE 3VCE *
CH 15 - IDLE TIE 3VCE * CH 16 - IDLE TIE 3VCE *
CH 17 - IDLE TIE 3VCE * CH 18 - IDLE TIE 3VCE *
CH 19 - IDLE TIE 3VCE * CH 20 - IDLE TIE 3VCE *
CH 21 - IDLE TIE 3VCE * CH 22 - IDLE TIE 3VCE *
CH 23 - IDLE TIE 3VCE * CH 24 - DCH 20
.
HERE IS MY ROUT 102

TYPE RDB
CUST 00
ROUT 102
DES IVR
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 5678
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

Can anyone post a working config I can try?

Thanks in advance,

 

[johnpoole]

what's broke on your tie? can your remote use qsig?

john poole
bellsouth business
columbia,sc

 

[zoomaster]

Hi Thanks for asking but we seem to have one of the TIE lines working. I am set as SL1 and Audiocodes gateway is set as D100 now. It appears my loop 11 with the Dch was plugged into gateway port 2 - which was set up with a D ch. When I moved the loop 11 to port 1 and vendor configuired it for D ch then the loop 11 came up and conversations both way. But for some reason loop 34 our 2nd TIE cannot make or receive calls. Loop 34 shows idle but when gateway makes a call to it we get protocol error. Now vendor is looking for his support people to figure out configuration problem at gateway end.