Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CS1000M, single group, Split cores

Status
Not open for further replies.

lliesbthighs

Vendor
Jun 29, 2008
152
Hi, it is newly installed CS1000M, singlr group, Release 5 (CPPIV). Below is some capture. Could some body guide some tips in this

LD 135-->STAT Health took from Core0, J25
------------------------------------------

.stat health
Local (Side 0, Active, Split):
Components without TIER 1 Health contribution:
==================================================
disp 0 15 1:In Service
sio2 0 15 1:In Service
cp 0 16:In Service
ipb 0:In Service

TIER 1 Health Count Breakdown:
=====================================
sio8 0 16 1: 0002
sio8 0 16 2: 0002
sutl 0 15: 0002
strn 0 15: 0002
xsmp 0 15 1: 0002
cnib 0 9: 0002
cnip 0 9 0: 0002
cnip 0 9 1: 0000 (OutOfService)
fmd 0 16 1: 0008
eth 0 16 0: 0000 (OutOfService)
Local TIER 1 Health Total: 22


TIER 2 Health Count Breakdown:
=======================================

Local AML over ELAN Total Health:0
Local Total IPL Health = 0

IPL connection history:0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Local TIER 2 Health Total:0

Remote (Side 1, Inactive, Split):

(Remote side health is not available. )

.stat cni
----------
cni 0 9 0: remote = group 0 ENBL

cni 1 9 0: remote = group 0 ENBL
*************************************
LD 135-->STAT Health took from Core1, J25
------------------------------------------
.stat health
Local (Side 1, Inactive, Split):
Components without TIER 1 Health contribution:
==================================================
disp 1 15 1:In Service
sio2 1 15 1:In Service
cp 1 16:In Service
ipb 1:In Service

TIER 1 Health Count Breakdown:
=====================================
sio8 1 16 1: 0002
sio8 1 16 2: 0002
sutl 1 15: 0002
strn 1 15: 0002
xsmp 1 15 1: 0002
cnib 1 9: 0002
cnip 1 9 0: 0000
cnip 1 9 1: 0000
fmd 1 16 1: 0008
eth 1 16 0: 0002
Local TIER 1 Health Total: 22


TIER 2 Health Count Breakdown:
=======================================

Local AML over ELAN Total Health:0
Local Total IPL Health = 0

IPL connection history:0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Local TIER 2 Health Total:0

Remote (Side 0, Active, Split):

(Remote side health is not available. )

.stat cni
----------
cni 1 9 0: remote = group 0 DSBL: 23

cni 0 9 0: remote = group 0 ENBL


and when i STAT CPU in LD 135 it shows
cp 1 16 PASS -- STDBY

SYSTEM STATE = SPLIT
DISK STATE = SPLIT
HEALTH = 22
VERSION = May 23 2007, 00:01:30
Side = 1, DRAM SIZE = 512 MBytes

cp 0 16 PASS -- ENBL

SYSTEM STATE = SPLIT
DISK STATE = SPLIT
HEALTH = 24
VERSION = May 23 2007, 00:01:30
Side = 0, DRAM SIZE = 512 MBytes

=========================================
Summary of Local System Resource (side 1)
=========================================
File Descriptors
-----------------
alloc 55
free 1993
total 2048

Unprotected Heap (bytes)
------------------------
alloc 39006048
free 207777904
total 246783952

Protected Heap (bytes)
----------------------
alloc 923588
free 3270716

It is actually in a installation process. The CEQU data is given as

REQ prt
TYPE cequ

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL 004 012 024 N096
N100 V104 V112
SUPC
SUPF
DDCS
DTCS
XCT 000 016
TDS * 000 * 016
CONF * 001 * 017
MFSD * 000 * 016
PRI2 008 009 018 019
APVL
DTI2
MISP
SYNM 0
EXT0 3PE
CNI 009 000 000
EXT1 3PE
CNI 009 000 000
MCFN 509 MB

Could somebody help in this
Regards


 
are all your faceplate switches in the normal state? if so i would either bring cnip 0 9 1 up manually or ini

john poole
bellsouth business
columbia,sc
 
If all the switches are normal go to ld 135 and type join.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
I already tried INI, and complete power down option, all faceplate switches are enable, when i use JOIN command doesnt working and says use CUTOVR command and when i use CUTOVR system gets INI and after INI stays in split mode.
Regards
 
now do the join since the cutover has been done.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
same result when i try to join after using CUTOVR it again says try to use CUTOVR.
Regards
 
When i STAT CNI from Core1 J25 it prints

stat cni
----------
cni 1 9 0: remote = group 0 DSBL: 23---->What it refer??

cni 0 9 0: remote = group 0 ENBL
However when i STAT CNI from J25 Core0 it shows both enable.

Regards,
 
You need to have someone check over the switch to ensure all the cabling is in the correct places. Sounds to me like something is wrong with the cabling that is not allowing the system to rejoin into a redundant mode. There are no special tricks to make it redundant.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Do you mean LAN2 cross cable and 3PE cables???As far as i understand there are 2 ports on CNI. am i correct and one port isnt enable in this case.
I can ping both CPU from LD 117. it means crossover LAN2 cable is OK. what other cable do i check? please advice?
Regards
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top