Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

cs1000e r5.5 tmdi issue

Status
Not open for further replies.

bigguyhawaii

Vendor
Jun 22, 2006
73
US
hi,

i'm installing a cs1000e rels 5.5 and i have 2 tmdi cards in the main cab on slots 3 and 4. slot 0 mgc,1 cs, 2 ss. i am able to program the tmdi cards, provision the clock and enable the tmdi in slot 3. but though the system can see the programming for the card in slot 4, when i try to enable it nothing happens. i swap cards 3 and 4 and the new card in 3 comes up but the original slot 3 card won't enable in slot 4. i've lost my hair already lol! is there an issue with 2 tmdi in the main cab? can u put a tmdi on slot 4? any help would be much appreciated.

aloha
 
The TMDI's are very flaky. In LD 48 can you see the tmdi as enabled? Are you getting any error codes, if so post them. One last
thing have you tried an INI or SYSLOAD? You may just have to
"Burp the Baby" to get them to act right.
 
no i can enable the tmdi in slot 3 (i can use both cards in slot 3 and it will enable). but i can't enable the tmdi card in slot 4, it sees the card but it shows up as disable in load 48 or 96. when i try to enable - enl tmdi 4 0 4 fdl - in load 48/96 it just sits there no error or return message, i have to 4 star out. i moved the card to a different shelf and it comes up but i don't know how to reference the clock to another shelf when the clock controller is sitting on loop 4 slot 3. when i tried to sref to the slot on the other loop i get an error. so i'm back at trying to make the 2nd card work on loop 4
 
Have you installed the latest TMDI loadware patch yet? I believe it is 19. I have seen this without this patch installed.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
i will check but is this loadware for the card or for the switch itself? the card works in slot 3 but not in slot 4. we've tried 2 different cards with the same problem.
 
LD 22 ISSP will show if it is installed. It will start like T1E1xxx.lw for patch file name. I can't remember what the XXX was at the moment.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Ok somebody enlighten me, from everything I can find the TMDI card is not compatible with the CS1000E. At least not with rls 4.5, did that change with 5.5 or are the books wrong. It would not surprise if that's the case.
 
That changed with 5.0 with the introduction of the MGC card. Media gateway must have a MGC card. SSC will not work.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top