Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CS1000E/Modular Messaging QSIG Integration Digits Issue

Status
Not open for further replies.

osheros

IS-IT--Management
Mar 26, 2008
23
US
I've inherited a Nortel CS1000E rev5 at another company we bought, so I'm a little new here. I've been tasked with integrating Avaya Modular Messaging via QSIG T1. I'm using a Dialogic 480JCT/2T1, but only one span.

Overall the integration works fine except when a call hunts from the first SCR to the second SCR. The second SCR on everybody's phone is a fictious, unpublished extension (the primary DN plus a "5" prepended to the front). It's setup this way so an incoming call doesn't flash two buttons at the same time. Guess that was too confusing for people.

Anyway, if the first SCR is in-use, when the call hunts to the second SCR and then to MM, the PBX is prepending the location code to the digits sent to MM instead of sending only the primary DN. I've looked all over the Avaya integration notes and don't see anything I've missed. I have all of the options that I need and, like I said, the integration works as long as the call is from the primary SCR (i.e. the phone is completely idle).

Any thoughts? I can send a config prt for whatever you need.

-Sam
 
Thanks for the reply. I'll start with a DNB:

DN 1051
CPND
NAME Keith Smith
XPLN 27
DISPLAY_FMT FIRST,LAST
TYPE SL1
TN 100 0 03 01 V KEY 00 H MARP DES AAAA 27 MAY 2010
(2004P2)
---------------------------
Here's the TNB:

DES AAAA
TN 100 0 03 01 VIRTUAL
TYPE 2004P2
CDEN 8D
CTYP XDLC
CUST 0
NUID
NHTN
CFG_ZONE 046
CUR_ZONE 046
ERL
ECL 0
FDN 1002
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 100
SCI 0
SSU
LNRS 16
XLST
CLS CTD FBD WTA LPR PUA MTD FNA HTA ADD HFA CRPD
MWA LMPN RMMD SMWD AAD IMD XHD IRA NIA OLA VCE DRG1
POD DSX VMD SLKD CCSD SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUA DNDA CFXA ARHD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
DRDD EXR0
USMD USRD ULAD RTDD RBDD RBHD PGND OCBD FLXA FTTC DNDY DNO3 MCBN
VOLA VOUA CDMR ICRD MCDD T87D KEM2 MSNV FRA PKCH
CPND_LANG ENG
RCO 0
HUNT 1002
LHK 1
LPK 0
PLEV 02
DANI NO
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
MLNG ENG
DNDR 0
DTMK
KEY 00 SCR 1051 0 MARP
CPND
NAME Keith Smith
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 51051 D MARP
CPND
NAME Keith Smith
XPLN 27
DISPLAY_FMT FIRST,LAST
02 ADL 16
03 ADL 16
04 ADL 16
05 ADL 16
06 ADL 16
07 ADL 16
08 ADL 16
09 ADL 16
10 ADL 16
11 ADL 16
12
13
14
15
16 MWK 1002
17 TRN
18 AO6
19 CFW 8 1002
20 RGA
21 PRK
22 RNP
23 SCC 0222
24 PRS
25 CHG
26 CPN
27
28
29
30
31
DATE 27 MAY 2010
 
Nobody has any thoughts? I can post additional information. Please let me know.

Thanks,
Sam
 
Are you using an RLI/DMI Table? Try changing your CTYP on your DMI to CDP?
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top