Cs1000 Rls 7.5 Routing DPNSS calls to Sip Console

[Swampfire]

Hi there I have an incoming call route which is DPNSS provided by BT they currenty send me a 5 digit site location code then a 5 digit extension number for incoming calls.The issue is that i can need to create a DSC for the site ID which deletes the 5 digits and routes the calls to my operator consoles which are conncted via sip trunks. This sends all incoming calls straight to the Sip route
FEAT cdp
TYPE dsc
DSC 74619
DSC 74619
FLEN 10
DSP LSC
RRPA NO
RLI 201
NPA
NXX

This works fine but my issue is that I have extensions on the switch which also require to get calls however with this setup I can not route calls to anything else other than the sip route.
I have tried to set the 5 digit site id as a LSC which works the opposite way i.e I can route calls to extension but the LSC will not route to a DSC. I then tried setting my numbers to route to the operators as phantom extensions but this caused an issue in that when 2 calls came in similtaneously one of the got busy. I checked this by dialling local the phantom and this worked everytime(MY Incoming trunks werent not all used)

I have tried enabling plugin 4 which says lsc to dsc recieves overflow tone but this doesnt work for external calls in on the DPNSS route it does work for internal calls if i dial LSC then a DSC to the SIp route. Printouts of both routes below I have also tried enabling vancant number routing against the net setting this works for internal calls but not the external calls in on the DPnss route any advise would be great.
TYPE: rdb
CUST 0
ROUT 100

TYPE RDB
CUST 00
ROUT 100
DES FXFCxxxxxx
TKTP IDA
NPID_TBL_NUM 0
SIGL DPN
CNVT NO
RCLS EXT
VTRK NO
DTRK NO
INAC NO
SPN NO
DSEL VOD
CNDP UKWN
AUTO NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 14900
TARG
CLEN 1
BILN NO
INST
TIMR EOD 13952
RMA 20480
SRM 32640
RAS 13952
NRAG 30
VSS 0
VGD 30
DRNG NO
CDR NO
NATL YES
CFWR NO
IDOP YES
VRAT NO
MUS NO
PANS YES
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
TTBL 0
ACNI NO
PLEV 2
ALRM NO
ART 1
SGRP 0
ARDN NO
CTBL 0
AACR NO

TYPE: rdb
CUST 0
ROUT 99

TYPE RDB
CUST 00
ROUT 99
DES VIRTTRK
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS INT
VTRK YES
ZONE 00099
PCID SIP
CRID NO
NODE 1000
DTRK NO
ISDN YES
MODE ISLD
DCH 99
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO YES
FALT NO
CTYP CDP
INAC NO
ISAR NO
DAPC NO
MBXR NO
MBXOT NPA
MBXT 0
PTYP ATT
CNDP UKWN
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 14902
TCPP NO
PII NO
AUXP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 1 *
NDNO 2
DEXT NO
SIGO ESN5
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256


PAGE 002

DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 30
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 1
PECL NO
DCTI 0
TIDY 85099 99
ATRR NO


PAGE 003

TRRL NO
SGRP 0
ARDN NO
CTBL 0
AACR NO

REQ:

 

[Firebird Scrambler]

When you tried using Phantom DN's, did you set up CLS = SFA as this enables more than one call to pass through.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[Firebird Scrambler]

With DPNSS, you can't use IDC. Therefore you have to use LSC in LD 87. However, with LSC's, you can also use a DMI to change the digit translation.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[Swampfire]

Thanks Firebirdscrambler I did have the sfa enabled it was fine if it was 2 internal calls but not when it was 2 external. I have used the DMI table to delete the site ID, issue was when the site ID is set as a LSC it will not route to a DSC which I have set up as to route the numbers to be answered by my sip consoles

DES DIVERT
TN 096 0 01 05 PHANTOM
TYPE 500
CDEN 4D
CUST 0
MRT
ERL 00000
WRLS NO
DN 24700 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS UNR DTN FBD XFD WTA THFD FNA HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD LPD XHD SLKD CCSD LND TVD
CFTD SFA MRD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXA ARHD OVDD AGTD CLTD LDTD ASCD SDND
MBXD CPFA CPTA UDI RCC HBTD IRGD DDGA NAMA MIND
NRWD NRCD NROD SPKD CRD PRSD MCRD
EXR0 SHL SMSD ABDD CFHD DNDY DNO3
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTU
FDSD NOVD CDMR PRED MCDD T87D SBMD PKCH MPTD ELCD
RCO 0
PLEV 02
PUID
UPWD
AACS NO
MLWU_LANG 0
FTR DCFW 8 17100
DATE 23 OCT 2012


NACT

 

[SL1M1]

Try using TrunkSteeringCode' TSC rather than DSC
let us know

Cheers!!

 

[Firebird Scrambler]

Instead of using Phantom DN's, have you tried just with a ACD queue and NCFW?.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.