Hi All,
I upgraded the bios of a CPPM CS (not coresident with SS) to 18 and reset the bios to factory default, whenever I reset the card i get 'ACPI initialization failure', check the below:
00000589K Low Memory Passed
01035136K Ext Memory Passed
Wait.....
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 3580 Host Bridge
00 00 01 8086 3584 System
00 00 03 8086 3585 System
00 01 00 8086 3581 PCI-to-PCI Bridge
00 02 00 8086 3582 VGA Display 12
00 1D 00 8086 24C2 Serial Bus 12
00 1D 01 8086 24C4 Serial Bus 11 Revision 5.3
00 1D 07 8086 24CD Serial Bus 10ights reserved.
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 24C0 ISA Bridge
00 1F 01 8086 24CB IDE Controller 9
00 1F 03 8086 24C3 Serial Bus 7
02 00 00 104C AC56 CardBus Bridge 11
02 01 00 8086 1209 Ethernet 12
02 02 00 8086 1209 Ethernet 7
02 03 00 8086 1078 Ethernet 9
Plug-n-Play v1.0A Copyright (C) 2005 General Software, Inc.
Polling Hard Drive and Compact Flash Locations
ACPI initialization failure <-----------------------
Press Any Key to Continue...
I overpassed this issue by disabling the ACPI 1.0 feature in Bios. I want to make sure that this wont affect the CS behaviour with ACPI 1.0 disabled because the document says 'reset to factory default' after bios upgrade wich set the ACPI to enabled. has anyone encountered the above?
Regards
I upgraded the bios of a CPPM CS (not coresident with SS) to 18 and reset the bios to factory default, whenever I reset the card i get 'ACPI initialization failure', check the below:
00000589K Low Memory Passed
01035136K Ext Memory Passed
Wait.....
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 3580 Host Bridge
00 00 01 8086 3584 System
00 00 03 8086 3585 System
00 01 00 8086 3581 PCI-to-PCI Bridge
00 02 00 8086 3582 VGA Display 12
00 1D 00 8086 24C2 Serial Bus 12
00 1D 01 8086 24C4 Serial Bus 11 Revision 5.3
00 1D 07 8086 24CD Serial Bus 10ights reserved.
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 24C0 ISA Bridge
00 1F 01 8086 24CB IDE Controller 9
00 1F 03 8086 24C3 Serial Bus 7
02 00 00 104C AC56 CardBus Bridge 11
02 01 00 8086 1209 Ethernet 12
02 02 00 8086 1209 Ethernet 7
02 03 00 8086 1078 Ethernet 9
Plug-n-Play v1.0A Copyright (C) 2005 General Software, Inc.
Polling Hard Drive and Compact Flash Locations
ACPI initialization failure <-----------------------
Press Any Key to Continue...
I overpassed this issue by disabling the ACPI 1.0 feature in Bios. I want to make sure that this wont affect the CS behaviour with ACPI 1.0 disabled because the document says 'reset to factory default' after bios upgrade wich set the ACPI to enabled. has anyone encountered the above?
Regards
